SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
Specification
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65.
Specification
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65
TAPE COTTON 19 MM OG SPECIAL IS : 3255-1979 Except that :-
(i) The specified Picks Density is minimum.
(ii) The Density of Weft Yarn may be halved and Picks density (minimum) double in case of Needle Loom manufacturing.
(iii) In appearance shade, finish & in all other respect not defined in this IS Specn. The material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, Kanpur.
(iv) There shall be no presence of starch.
(v) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent).
(vi) 100% Sampling Testing & Inspection will be resorted to. Sampling plan as per annexure (a) attached. Packing and marking as per schedule CIT&C/PMS/65.
SPECIFICATION NO. : ADRDE/SPECN/1993/44(a) ROLL LENGTH 100 MTR. EXCLUDING SAMPLING.
Except that : - Shade should be as per approved sample held with QCM/OPF.
SPECN.NO.: IS:3255-1979 except that :-
(i)In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the
sealed pattern held of the custody of the controller,CQAT&C, Kanpur. (ii)There shall be no presence of strach. (iii)End in full width to be raised by 2. (iv)Pick/cm(-1) Tolerance to be premitted. (v)100% Sampling/testing/inspection shall be resorted to. (vi) Scouring loss-Mild method is to be followed in view of severe method & shall not except 2%(two percent).
(vii) Sampling plan as per annexure (A) attached.
Specification
SPECN.NO.: IS:3255-1979 except that :-
(i)In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the
sealed pattern held of the custody of the controller,CQAT&C, Kanpur. (ii)There shall be no presence of strach. (iii)End in full width to be raised by 2. (iv)Pick/cm(-1) Tolerance to be premitted. (v)100% Sampling/testing/inspection shall be resorted to. (vi) Scouring loss-Mild method is to be followed in view of severe method & shall not except 2%(two percent).
(vii) Sampling plan as per annexure (A) attached.
1--Width(mm) ---12.7 mm. Appendix B of IS:3846:1984
2--Mass(gm/mt.)--- 8(max). Appendix C of IS:3846:1984
3--Ends in full/width)--- 60+3/-0. IS:1963
4--Picks/cm --- 20+2/-0 (total picks based on two thread working as one. IS:1963
5--Breaking load(20 cm X Full width)("KN.") Minimum-- 1.5 IS:1969
6--Nature of material-- 100% Polyster. IS:667
7--pH Value (Cold Method)--6 to 8.5. IS:1390
8--% Water soluble matter (max)---1%. IS: 3456
9--Weave--- 2/2 Twill weave. Visual
Specification
1--Width(mm) ---12.7 mm. Appendix B of IS:3846:1984
2--Mass(gm/mt.)--- 8(max). Appendix C of IS:3846:1984
3--Ends in full/width)--- 60+3/-0. IS:1963
4--Picks/cm --- 20+2/-0 (total picks based on two thread working as one. IS:1963
5--Breaking load(20 cm X Full width)("KN.") Minimum-- 1.5 IS:1969
6--Nature of material-- 100% Polyster. IS:667
7--pH Value (Cold Method)--6 to 8.5. IS:1390
8--% Water soluble matter (max)---1%. IS: 3456
9--Weave--- 2/2 Twill weave. Visual
1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984
2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984
3- Ends(in full/width)------ 85+4/-0. IS:1963
4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963
5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969
6- Nature of material--100% Polyster. IS:667
7- pH Value(Cold Method)--6 to 8.5. IS:1390
8- % Water soluble matter(max)-- 1%. IS:3456
9- Weave-- 2/2 Twill weave. Visual
Specification
1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984
2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984
3- Ends(in full/width)------ 85+4/-0. IS:1963
4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963
5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969
6- Nature of material--100% Polyster. IS:667
7- pH Value(Cold Method)--6 to 8.5. IS:1390
8- % Water soluble matter(max)-- 1%. IS:3456
9- Weave-- 2/2 Twill weave. Visual
HEIDENHAIN MAKE ENCODER TYPE ERN 1387.001-2048 B4 5V +/- 5%, ID.NR.312 215-14, 1.1V SS OR COMPATIBLE UNIT TYPE: ERN 1387X2048 ID:385487-51 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE
Specification
HEIDENHAIN MAKE ENCODER TYPE ERN 1387.001-2048 B4 5V +/- 5%, ID.NR.312 215-14, 1.1V SS OR COMPATIBLE UNIT TYPE: ERN 1387X2048 ID:385487-51 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE
HEIDENHAIN MAKE ENCODER TYPE ERN 1381.001-2048, W8 5V +/- 5% ID.NR.313 453-02,1V SS OR COMPATIBLE UNIT TYPE:ERN 1381X2048 ID:385489-56 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE .
Specification
HEIDENHAIN MAKE ENCODER TYPE ERN 1381.001-2048, W8 5V +/- 5% ID.NR.313 453-02,1V SS OR COMPATIBLE UNIT TYPE:ERN 1381X2048 ID:385489-56 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE .
ABSOLUTE SEALED LINEAR ENCODER/SCALE, TYPE LC493F; 50NM, ID 557644-04, MEASURING LENGTH 220MM, ACCURACY GRADE, MEASURING STEP1: 12.5000NM, MEASURING STEP2: 50.0000NM, OR SUCCESSOR LC495F, ID 760932-04, WITH SCANNING HEAD AND END BLOCK+MOUNT ING SPAR, MAKE: HEIDENHAIN
Specification
ABSOLUTE SEALED LINEAR ENCODER/SCALE, TYPE LC493F; 50NM, ID 557644-04, MEASURING LENGTH 220MM, ACCURACY GRADE, MEASURING STEP1: 12.5000NM, MEASURING STEP2: 50.0000NM, OR SUCCESSOR LC495F, ID 760932-04, WITH SCANNING HEAD AND END BLOCK+MOUNT ING SPAR, MAKE: HEIDENHAIN
HYDRAULIC OIL FILTER LF.1001 ELEMENT INTERNORMAN MODEL: 01. .NR 1000.6VG.10.B.P. PART NO:305449 EQUIVALLENT MAKE OF HYDA C, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
Specification
HYDRAULIC OIL FILTER LF.1001 ELEMENT INTERNORMAN MODEL: 01. .NR 1000.6VG.10.B.P. PART NO:305449 EQUIVALLENT MAKE OF HYDA C, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
RETURN LINE HYDRAULIC OIL FILTER ELEMENT INTERNORMAN MODEL: 01.E.360.10VG.30.E.P. PART NO:300231, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITM ENT GUARANTEE ON MACHIN
Specification
RETURN LINE HYDRAULIC OIL FILTER ELEMENT INTERNORMAN MODEL: 01.E.360.10VG.30.E.P. PART NO:300231, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITM ENT GUARANTEE ON MACHIN
HIGH PRESSURE HYDRAULIC OIL FILTER HP.601.ELEMENT INTERNORME N MODEL- 01.E 600.10VG.30.E.P. PART NO-300265, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
Specification
HIGH PRESSURE HYDRAULIC OIL FILTER HP.601.ELEMENT INTERNORME N MODEL- 01.E 600.10VG.30.E.P. PART NO-300265, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
20
30
Number
35285
RFI/REGD/ESTT./IC/2018
Rifle Factory Ishapur
The General Manager,
Ishapore
Ishapore
West Bengal
743144
INVESTMENT CASTING OF BRACKET(WITH HEAT TREATMENT)AS PER RFI SK.NO.6756*3-S(I.C TO BE SUPPLIED IN HARDNESS RANGE OF 248 TO 280 HB.) FOR RIFLE 5.56MM.INSAS.
Specification
bs
Drawing no.
AS PER RFI SK.NO.6756*3-S(I.C TO BE SUPPLIED IN HARDNESS RANGE OF 248 TO 280 HB.)
