COVER TO DRG.3-027321-4B2-21,DC NO: 36050-A,DT.05.12.95

COVER TO DRG.3-027321-4B2-21,DC NO: 36050-A,DT.05.12.95

ELECTRIC FUZE UNCHARGED TO DRG.NO: 3-027321-4B2-Cd-8, DCI.33760A, DT.04.06.1985. SPECIAL REQUIREMENT: RESISTANCE ACROSS THE POINTS OF Pt-Ir WIRE SHOULD BE 1.4 TO 1.8 OMHS.

ELECTRIC FUZE UNCHARGED TO DRG.NO: 3-027321-4B2-Cd-8, DCI.33760A, DT.04.06.1985. SPECIAL REQUIREMENT: RESISTANCE ACROSS THE POINTS OF Pt-Ir WIRE SHOULD BE 1.4 TO 1.8 OMHS.

SCREW SET SLOTTED HEAD,FULL DOG POINT NO.2BA TO DESIGNER'S REF.NO.CIA/AMN/885,DC NO.33833-A, DT.19.12.87

SCREW SET SLOTTED HEAD,FULL DOG POINT NO.2BA TO DESIGNER'S REF.NO.CIA/AMN/885,DC NO.33833-A, DT.19.12.87

FUZE PERCUSSION DA NO.117 (EMPTY) MK.20 WITH CAP TO DESIGNERS REF NO.L5/10744/GE/341, PART NO: QX-244 GE,DC NO. 31398-A,DT.10.02.75. (REF.DRG.FUZE PERCUSSION DA NO.117 EMPTY MK 20 ITEM LIST FOR QX 244 GE DCI-31398-A DT.10.02.75)

FUZE PERCUSSION DA NO.117 (EMPTY) MK.20 WITH CAP TO DESIGNERS REF NO.L5/10744/GE/341, PART NO: QX-244 GE,DC NO. 31398-A,DT.10.02.75. (REF.DRG.FUZE PERCUSSION DA NO.117 EMPTY MK 20 ITEM LIST FOR QX 244 GE DCI-31398-A DT.10.02.75)

KEY AMMUNITION 39A TO DRG PART NO. IUX 144A,DC NO.35916-A,DT.21.02.95 TO SPECN.CQA(A) 1817(t) DC 37096-A,DT.06.03.2007.

KEY AMMUNITION 39A TO DRG PART NO. IUX 144A,DC NO.35916-A,DT.21.02.95 TO SPECN.CQA(A) 1817(t) DC 37096-A,DT.06.03.2007.

CLIPS, 25.41MM(L)X13MM(W)X0.3MM(T) SEAL TIN(FOR STEEL TAPE BANDING SIZE 13MM WIDE) APPROX. SIZE 25.41MM LENGTH X 12.7MM WIDTH X 0.3MM THICK AND BAND OF 90 DEGREE ANGLE BOTH SIDE LONGITUDINALLY WITH HEIGHT 6.3MM.

CLIPS, 25.41MM(L)X13MM(W)X0.3MM(T) SEAL TIN(FOR STEEL TAPE BANDING SIZE 13MM WIDE) APPROX. SIZE 25.41MM LENGTH X 12.7MM WIDTH X 0.3MM THICK AND BAND OF 90 DEGREE ANGLE BOTH SIDE LONGITUDINALLY WITH HEIGHT 6.3MM.

BODY WITH BAND [FOR 30MM AP(T)] TO DRG.NO.bw 5.500.113/C,DC NO.37321-A,DT-18.10.12 [USING WITH BODY (ALTERNATIVE) TO DRG.NO.bW 8.035.085/C SHEET 3 & 4 DC NO.34640-A,DT-9.6.89]. REF:(1) BODY WITH ASSY. DRAWING bW 5.500.113 Cb/c DC(1)-34183-A Dt.28.07.87(2) BODY WITH DRIVING BEND PROG & TEST PROCEDURE bW 5.500.113 M/C DC(1)34183-A DT.28.07.87 (09 SHEETS)

BODY WITH BAND [FOR 30MM AP(T)] TO DRG.NO.bw 5.500.113/C,DC NO.37321-A,DT-18.10.12 [USING WITH BODY (ALTERNATIVE) TO DRG.NO.bW 8.035.085/C SHEET 3 & 4 DC NO.34640-A,DT-9.6.89]. REF:(1) BODY WITH ASSY. DRAWING bW 5.500.113 Cb/c DC(1)-34183-A Dt.28.07.87(2) BODY WITH DRIVING BEND PROG & TEST PROCEDURE bW 5.500.113 M/C DC(1)34183-A DT.28.07.87 (09 SHEETS)

CUP: DRG.9-04367/9- -104/ 38.350. 189,DC.NO-36309-A,DT.14.07.97

CUP: DRG.9-04367/9- -104/ 38.350. 189,DC.NO-36309-A,DT.14.07.97

NOSE FUZE TYPE A 670M (EMPTY) FOR 30MM BMP-II AMMN. TO CQA(A) DRG.NO.bw.3.140.039.cb/c,DC-34241-A, DT.24.9.87(IN LOOSLY ASSEMBLED CONDITION) CONSISTING OF VARIOUS COMPONENTS AS PER ENCLOSED LIST(PASSED PROOF). PROGRAMME AND TEST PROCEDURE AS PER ALBUM NO. D-2040, SHEET NO.Bw.3.140.039 II M/c (12 SHEETS) DC-34241-A, DT.24.09.87.

NOSE FUZE TYPE A 670M (EMPTY) FOR 30MM BMP-II AMMN. TO CQA(A) DRG.NO.bw.3.140.039.cb/c,DC-34241-A, DT.24.9.87(IN LOOSLY ASSEMBLED CONDITION) CONSISTING OF VARIOUS COMPONENTS AS PER ENCLOSED LIST(PASSED PROOF). PROGRAMME AND TEST PROCEDURE AS PER ALBUM NO. D-2040, SHEET NO.Bw.3.140.039 II M/c (12 SHEETS) DC-34241-A, DT.24.09.87.

• CNC MILLING CENTER , CNC TURNING CENTER, DRILLING FACILITY, GRINDING FACILITY,CNC AUTOMATIC MACHINE ( MINIMUM 6 AXIS) HAVING CAPABILITY TO COMPLETE ALL OPERATIONS OF PLUG ( COMPONENT TO A670M FUZE) IN ONE OR TWO SETTINGS
• DESIRABLE: VACCUM FURNACE FOR HEAT TREATMENT OF COPPER SPIRAL & OTHER COMPONENT.

• SURFACE TREATMENT FACILITY AS PER DRAWING, SPINNING TESTING FACILITY, SUITABLE IN PROCESS TESTING FACILITY AS PER DRAWING, SUITABLE MEASUNG FACILITY

BODY TO DRG.NO.9-04367/9- -104/ 38.300.150, DC NO.36396-A DT-21.03.98.

BODY TO DRG.NO.9-04367/9- -104/ 38.300.150, DC NO.36396-A DT-21.03.98.

DISC: DRG.9-04367/9- -104/ 38.366. 113, DC.NO.36309-A, DT-14.07.97.

DISC: DRG.9-04367/9- -104/ 38.366. 113, DC.NO.36309-A, DT-14.07.97.

ANVIL FOR CARTG.3G/51MM TO DRG.NO. DDL-12002, ASSY. DRG.DD(L)17235 FOR 51MM MORTAR BOMB. DC NO-37286-A ,DT-09.09.2011

ANVIL FOR CARTG.3G/51MM TO DRG.NO. DDL-12002, ASSY. DRG.DD(L)17235 FOR 51MM MORTAR BOMB. DC NO-37286-A ,DT-09.09.2011

51MM MORTAR BOMB BODY(EMPTY) TO PT. NO.ITV 17 SA (02 SHEETS),SHEET NO.01 DC 37111-A DT.21.05.07 & SHEET-2, DC 37193-A DT.13.11.08.

51MM MORTAR BOMB BODY(EMPTY) TO PT. NO.ITV 17 SA (02 SHEETS),SHEET NO.01 DC 37111-A DT.21.05.07 & SHEET-2, DC 37193-A DT.13.11.08.

NOTCHED COIL TO ARDE 1933 PART ITV- 169 DETAIL NO.3, DC.36529-A,DT.06.03.2008.

NOTCHED COIL TO ARDE 1933 PART ITV- 169 DETAIL NO.3, DC.36529-A,DT.06.03.2008.

FIRE TRANSMITTING TUBES MKG.51MM TO ARDE-1934, IRW 203. DCNO.37068-A DT.14.09.2006.

FIRE TRANSMITTING TUBES MKG.51MM TO ARDE-1934, IRW 203. DCNO.37068-A DT.14.09.2006.

FUZE DA5A (EMPTY) FOR 51MM MORTAR BOMB, IQX 79 GE TO DC 37263-A DT.26.08.2010.

FUZE DA5A (EMPTY) FOR 51MM MORTAR BOMB, IQX 79 GE TO DC 37263-A DT.26.08.2010.

RING TO DRG.NO.1933 DET.NO.6 TO PT. ITV 172.DC-36529-A DT.18-02-99.

RING TO DRG.NO.1933 DET.NO.6 TO PT. ITV 172.DC-36529-A DT.18-02-99.

COLLAR NOSE TO DRG.NO.PART NO - ISV 1942 DC-36202-A DT. 07-11-96

COLLAR NOSE TO DRG.NO.PART NO - ISV 1942 DC-36202-A DT. 07-11-96

CAP COMPLETE (3 G CAP EMPTY) TO REF. NO.DD(L)17235 FOR CARTG. 3G/51MM, SHEET-1 DC-36972-A, DT.27.07.04,SHEET-2 DC 36972-A DT.27.07.04.

CAP COMPLETE (3 G CAP EMPTY) TO REF. NO.DD(L)17235 FOR CARTG. 3G/51MM, SHEET-1 DC-36972-A, DT.27.07.04,SHEET-2 DC 36972-A DT.27.07.04.

DISC TO PART NO.QX-41AF,ITEM NO:2 MATERIAL SPECN: LEAD TIN FOILTO JSS:9535-06-2010(REV.NO-2), DC NO:4085-ME, DTD.08.09.2010(FOR CAP 78G). NOTE:TOP OF THE TIN FOIL DISC TO BE COATED WITH VARNISH SHELLAC.

DISC TO PART NO.QX-41AF,ITEM NO:2 MATERIAL SPECN: LEAD TIN FOILTO JSS:9535-06-2010(REV.NO-2), DC NO:4085-ME, DTD.08.09.2010(FOR CAP 78G). NOTE:TOP OF THE TIN FOIL DISC TO BE COATED WITH VARNISH SHELLAC.

CASE TO DRG.PART NO.QX-172,DC NO. 35639-A DT.28.12.93, MATERIAL SPECN:COPPER ALLOY STRIP TO IS:3167-1982 (FIRST REVESION)(RA 1988)WITH HARDNESS 55 TO 75 VPN)

CASE TO DRG.PART NO.QX-172,DC NO. 35639-A DT.28.12.93, MATERIAL SPECN:COPPER ALLOY STRIP TO IS:3167-1982 (FIRST REVESION)(RA 1988)WITH HARDNESS 55 TO 75 VPN)

CONTAINER TO DRG.NO.4-24929/3 K 33/000,DC NO.36434-A,DT-6.7.98,CONSISTING OF THE FOLLOWING ITEMS. (1)BODY TO DRG.NO.4-24929/3 K33/010 , (2)COVER TO DRG.NO.4-24929/3 K33/020 DC 35604-A, (3)BOLT TO DRG.NO.4-24929/3 K33/030 (4)FORK TO DRG.NO.4-24929/3 K33/005, ALL THE 4NOS DRG'S STATED ABOVE TO DC NO.36434-A,DT.06.07.98

CONTAINER TO DRG.NO.4-24929/3 K 33/000,DC NO.36434-A,DT-6.7.98,CONSISTING OF THE FOLLOWING ITEMS. (1)BODY TO DRG.NO.4-24929/3 K33/010 , (2)COVER TO DRG.NO.4-24929/3 K33/020 DC 35604-A, (3)BOLT TO DRG.NO.4-24929/3 K33/030 (4)FORK TO DRG.NO.4-24929/3 K33/005, ALL THE 4NOS DRG'S STATED ABOVE TO DC NO.36434-A,DT.06.07.98

PLUG REPRESENTING FUZE B 429B TO DRG.NO:CQA (A)/AMN/1669 PART NO:ISX-266,DC NO-35494-A, DT. 29.04.93

PLUG REPRESENTING FUZE B 429B TO DRG.NO:CQA (A)/AMN/1669 PART NO:ISX-266,DC NO-35494-A, DT. 29.04.93

PRIMER PERCUSSION,Q.F CARTGS.18A (EMPTY)TO DRG.PART NO IQX-51GE,DC-36506-A,DT.23.12.98 WITH BODY AND MAGAZINE SEPARATELY (WITH OUT ASSEMBLED CONDITION)

PRIMER PERCUSSION,Q.F CARTGS.18A (EMPTY)TO DRG.PART NO IQX-51GE,DC-36506-A,DT.23.12.98 WITH BODY AND MAGAZINE SEPARATELY (WITH OUT ASSEMBLED CONDITION)

TOP PLUG TO OFAJ DRG.NO:S-78C (REF. DRG.NO.4079922,DC NO.36817-A,DT.08.03.2002,DULY SURFACE TREATED AS PER DRG.NO.5191819,DC NO.34810-A, DT.05.03.90 (PRF FOR 155MM M-107 & M77B )

TOP PLUG TO OFAJ DRG.NO:S-78C (REF. DRG.NO.4079922,DC NO.36817-A,DT.08.03.2002,DULY SURFACE TREATED AS PER DRG.NO.5191819,DC NO.34810-A, DT.05.03.90 (PRF FOR 155MM M-107 & M77B )

CASE: DRG.9-04367/9- -104/ 38.310. 032, DC.NO.36309-A, DT.14.07.97.

CASE: DRG.9-04367/9- -104/ 38.310. 032, DC.NO.36309-A, DT.14.07.97.

SLEEVE:DRG.9-04367/9- -104/ 38.316 .101,DC.NO.36309-A,DT.14.07.97.

SLEEVE:DRG.9-04367/9- -104/ 38.316 .101,DC.NO.36309-A,DT.14.07.97.

CAP: DRG.9-04367/9- -104/ 38.320. 262-DC.NO.36309-A, DT-14.07.97.

CAP: DRG.9-04367/9- -104/ 38.320. 262-DC.NO.36309-A, DT-14.07.97.

test

test

fdsfgsdgfds

TOP PLATE & BOTTOM PLATE AS PER DRG NO - LFVD/1000/32.

TOP PLATE & BOTTOM PLATE AS PER DRG NO - LFVD/1000/32.

DRG NO - LFVD/1000/32.

BOTTOM FLAT TOOL FOR 2650 MT FORGING PRESS DRG.NO.NGF/282 R2

BOTTOM FLAT TOOL FOR 2650 MT FORGING PRESS DRG.NO.NGF/282 R2

DRG.NO.NGF/282 R2

"M.S. STARTER PLATE SIZE - 20 MM X 1000 MM X 1200 MM AS PER MSF DRG NO - ESR/1000/03 . FULLY MACHINED AS PER DRAWING AND FITTED WITH BOSS -03 NOS IN EACH PLATE . "

"M.S. STARTER PLATE SIZE - 20 MM X 1000 MM X 1200 MM AS PER MSF DRG NO - ESR/1000/03 . FULLY MACHINED AS PER DRAWING AND FITTED WITH BOSS -03 NOS IN EACH PLATE . "

MSF DRG NO - ESR/1000/03

FERRO MOLYBDENUM TO SPECN IS:1469-1993,GR:Fe-Mo 63,C-10;CHEMCOMP.=Mo%:60-65,C%:0.10Mx,Si%:2.0Max,S%:0.08Max,P%:0.06MaxCu%:0.50Max,Al%:0.50Max,Pb%:0.01Max,Sn%:0.03Max.PARTICLE SIZE:Over 25 mm Upto and including 50 mm,Under size by mass:5%Max,Over size by mass:10%Max.OTHER REQUIREMENTS:AS PER SPECN

FERRO MOLYBDENUM TO SPECN IS:1469-1993,GR:Fe-Mo 63,C-10;CHEMCOMP.=Mo%:60-65,C%:0.10Mx,Si%:2.0Max,S%:0.08Max,P%:0.06MaxCu%:0.50Max,Al%:0.50Max,Pb%:0.01Max,Sn%:0.03Max.PARTICLE SIZE:Over 25 mm Upto and including 50 mm,Under size by mass:5%Max,Over size by mass:10%Max.OTHER REQUIREMENTS:AS PER SPECN

FERRO VANADIUM.TO SPECN.IS: 1466-1985,(Reaffirmed in 1996),GRADE-Fe V 55, (LC)(MATERIAL TO BE SUPPLIED IN SIZE BETWEEN 25MM TO 50MM).FIRM'S TEST CERTIFICATE FROM NABL ACCREDED LABY/GOVT.RECOGNISED LABY;AS PER SPECN.MUST BE ATTACHED WHILE SUPPLYING MATL

FERRO VANADIUM.TO SPECN.IS: 1466-1985,(Reaffirmed in 1996),GRADE-Fe V 55, (LC)(MATERIAL TO BE SUPPLIED IN SIZE BETWEEN 25MM TO 50MM).FIRM'S TEST CERTIFICATE FROM NABL ACCREDED LABY/GOVT.RECOGNISED LABY;AS PER SPECN.MUST BE ATTACHED WHILE SUPPLYING MATL

IRON ORE TO SPECIFICATION IS : 5442-1992, Gr.57/59, PARTICLE SIZE- 200 +10MM. FE CONTENT SHOULD BE MINIMUM 57%"

IRON ORE TO SPECIFICATION IS : 5442-1992, Gr.57/59, PARTICLE SIZE- 200 +10MM. FE CONTENT SHOULD BE MINIMUM 57%"

FERRO MANGANESE [H C] TO SPECN. IS - 1171-1996, GRADE-Fe Mn 72 [SIZE OF THE LUMPS 50 MM TO 150 MM WITH PERCENTAGE OF FINES LIMITED UP TO 10 %,]

FERRO MANGANESE [H C] TO SPECN. IS - 1171-1996, GRADE-Fe Mn 72 [SIZE OF THE LUMPS 50 MM TO 150 MM WITH PERCENTAGE OF FINES LIMITED UP TO 10 %,]

FERRO-CHROME ( HIGH CARBON ) TO SPECIFICATION IS: 1170-1992,GRADE- 1, DESIGNATION 7 Fe Cr-65, CHEM.COMP.:- Cr%:60-70,C%:6-8,Si%:1.5-4;RESIDUAL ELEMENTS & OTHERS: AS PER SPECN. PARTICLE SIZE: BETWEEN 100 MM TO 150 MM,UNDER SIZE: 5% MAX,OVERSIZE: 10% MAX. FREE FROM EXTRANEOUS CONTAMINATIONS ETC.

FERRO-CHROME ( HIGH CARBON ) TO SPECIFICATION IS: 1170-1992,GRADE- 1, DESIGNATION 7 Fe Cr-65, CHEM.COMP.:- Cr%:60-70,C%:6-8,Si%:1.5-4;RESIDUAL ELEMENTS & OTHERS: AS PER SPECN. PARTICLE SIZE: BETWEEN 100 MM TO 150 MM,UNDER SIZE: 5% MAX,OVERSIZE: 10% MAX. FREE FROM EXTRANEOUS CONTAMINATIONS ETC.

DOLOMITE FETTLING MASS FOR HOT REPAIR OF BANK AND BOTTOM OF EAF.CHEMICAL COMPOSITION: %MgO= 36 - 40,

DOLOMITE FETTLING MASS FOR HOT REPAIR OF BANK AND BOTTOM OF EAF.CHEMICAL COMPOSITION: %MgO= 36 - 40,

FLUORSPAR TO SPECIFICATION - IS-4574-1989 (REAFFIRMED-2003)GRADE-3 [COMPOSITION:CAF2-80 % MIN,SiO2-8% MAX,CaCO3 -3% MAX MIXED OXIDE(R2O3 - 3.5% MAX,S-0.3% MAX,Pb - 0.3% MAX).PELLET FORM HAVING SIZE - 1" TO 3".

FLUORSPAR TO SPECIFICATION - IS-4574-1989 (REAFFIRMED-2003)GRADE-3 [COMPOSITION:CAF2-80 % MIN,SiO2-8% MAX,CaCO3 -3% MAX MIXED OXIDE(R2O3 - 3.5% MAX,S-0.3% MAX,Pb - 0.3% MAX).PELLET FORM HAVING SIZE - 1" TO 3".

CRADLE CLAMP PART NO 1148547

CRADLE CLAMP PART NO 1148547

• as per Annexure L

• as per Annexure L

AL FLAT 120X85MM IS:733-1983,76528

AL FLAT 120X85MM IS:733-1983,76528

AL ANGLE 60X40X5 IS733-83,64430 WP

AL ANGLE 60X40X5 IS733-83,64430 WP

AL FLAT 130X100MM IS:733-1983,76528

AL FLAT 130X100MM IS:733-1983,76528

AL RD 95MM DIA IS:733-1983, 76528 WP

AL RD 95MM DIA IS:733-1983, 76528 WP

AL PLATE 2MM THICK IS:737-08,52000

AL PLATE 2MM THICK IS:737-08,52000

ST RD 55 MM DIA IS:5517-93,42CR4M02

ST RD 55 MM DIA IS:5517-93,42CR4M02

ST SQR 125MM IS 5517-78,40NI6C

ST SQR 125MM IS 5517-78,40NI6C

ST RD 150MM DIA IS:5517-1993,40NI6C

ST RD 150MM DIA IS:5517-1993,40NI6C

ST RD 32MM BS:970,PT-1-83,817,M40

ST RD 32MM BS:970,PT-1-83,817,M40

ST RD 80MM DIA EN 10297-1-2003,25CR

ST RD 80MM DIA EN 10297-1-2003,25CR

RD HSS 19MM DIA T70W18CR4VI

RD HSS 19MM DIA T70W18CR4VI

ST SHEET SIZE:1MM TH IS1570-61C-25

ST SHEET SIZE:1MM TH IS1570-61C-25

ST RD 12MM DIATO SPECN C-25

ST RD 12MM DIATO SPECN C-25

ST RD 90MM DIA IS:8500-91,GD.FE490B

ST RD 90MM DIA IS:8500-91,GD.FE490B

ST.RD.40MM IS:4431-78,GD.11C10S25

ST.RD.40MM IS:4431-78,GD.11C10S25

BRACKET INVEST CASTING 3053375D

BRACKET INVEST CASTING 3053375D

BRACKET INVESTMENT CAST.GCF/50/39183

BRACKET INVESTMENT CAST.GCF/50/39183

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

AS PER GCF SPECIFICATION.DRG/SIZE & REQUIREMENTS

RING PRONG SNAP BUTTON-9MM SHALL BE MADE AS PER MATERIAL GIVEN IN 4741-1968, ALL FOUR PARTS SHALL BE NIKLE-PLATED AND CONFORM TO GRADE-B OF IS:1068-1958. SNAP SHALL DISENGAGE WHENTHEY ARE SUBJECT TO PULL WITH 1.0 +/-0.3 kgf APPLIED ALONGITS CENTRE LINE ASPER ASTM D4846- 96(REAPPROVED 2011).DESIGN/DIMENSIONS AS PER SAMPLE HELD IN CQA(T&C),KANPUR.AS PER RELEVANT CLAUSE OF SPECIFICATIONA

RING PRONG SNAP BUTTON-9MM SHALL BE MADE AS PER MATERIAL GIVEN IN 4741-1968, ALL FOUR PARTS SHALL BE NIKLE-PLATED AND CONFORM TO GRADE-B OF IS:1068-1958. SNAP SHALL DISENGAGE WHENTHEY ARE SUBJECT TO PULL WITH 1.0 +/-0.3 kgf APPLIED ALONGITS CENTRE LINE ASPER ASTM D4846- 96(REAPPROVED 2011).DESIGN/DIMENSIONS AS PER SAMPLE HELD IN CQA(T&C),KANPUR.AS PER RELEVANT CLAUSE OF SPECIFICATIONA

HIGH ALUMINA REFRACTORY CEMENT. TRADE NAME :"WHYTHEAT GRADE LWB SPECN: Al2O3: 90%MIN.,SiO2:2 TO 3 %, Fe2O3:0.75% (0.80% MAX) MAX.SERVICE TEMPERATURE:1750 DEG.C.MAX.GRAIN SIZE :5 MM. PACKED IN 50 KGS HDPE BAGS.

HIGH ALUMINA REFRACTORY CEMENT. TRADE NAME :"WHYTHEAT GRADE LWB SPECN: Al2O3: 90%MIN.,SiO2:2 TO 3 %, Fe2O3:0.75% (0.80% MAX) MAX.SERVICE TEMPERATURE:1750 DEG.C.MAX.GRAIN SIZE :5 MM. PACKED IN 50 KGS HDPE BAGS.

GRAPHITE CRUCIBLE FOR LADDLE OF SLAG MELTING FURNACE AS PER MSF DRG NO. LFVD/1000/22 (SHEET NO.3/3)

GRAPHITE CRUCIBLE FOR LADDLE OF SLAG MELTING FURNACE AS PER MSF DRG NO. LFVD/1000/22 (SHEET NO.3/3)

MSF DRG NO. LFVD/1000/22 (SHEET NO.3/3)

BOTTOM POURING S.G IRON INGOT MOULD TO SIZE 385 MM DIA X2265 MM LONG AS PER DRG. NO. OH-391. MATERIAL SPECN. SPHEROIDAL CAST IRON IS:1865 GRADE:400/18. FIRM SHOULD SUBMIT T.C. FROM, NABL ACCREDITED/GOVT. APPROVED LAB ONLYFOR BASIC METAL & MECHANICAL PROPERTIES.

MATERIAL SPECN. SPHEROIDAL CAST IRON IS:1865 GRADE:400/18

DRG. NO. OH-391

BOTTOM POURING S.G.IRON INGOT MOULD TO SIZE 450 MM DIAX2250MM LG AS PER DRG. NO-O.H.-387. MATL. SPECN-SPHEROIDAL CASTIRON AS PER IS:1865 GRADE 400/18. FIRM SHALL SUBMIT T.C.FROMNABL ACCREDITED/GOVT APPROVED LAB. ONLY FOR BASIC MATERIALAND MECHANICAL PROPERTIES

SPECN-SPHEROIDAL CASTIRON AS PER IS:1865

DRG. NO-O.H.-387

BOTTOM PLATE FOR 20 TON EAF AS PER DRAWING NO:OH-385.

BOTTOM PLATE FOR 20 TON EAF AS PER DRAWING NO:OH-385.

DRAWING NO:OH-385

4 WAY 4 MOULD BOTTOM POURING SET FOR 20 TO EAF AS PER MSF DRAWING NO:0H-389.

4 WAY 4 MOULD BOTTOM POURING SET FOR 20 TO EAF AS PER MSF DRAWING NO:0H-389.

MSF DRAWING NO:0H-389.

4 WAY 8 MOULD BOTTOM POURING SET FOR 20 TON EAF AS PER MSF DRAWING NO:OH-390.

4 WAY 8 MOULD BOTTOM POURING SET FOR 20 TON EAF AS PER MSF DRAWING NO:OH-390.

MSF DRAWING NO:OH-390.

C. I. MOULD 23"FOR RADIAL FORGING AS PER DRG. NO. OH/1012/150/1 (R1)

C. I. MOULD 23"FOR RADIAL FORGING AS PER DRG. NO. OH/1012/150/1 (R1)

DRG. NO. OH/1012/150/1 (R1)

S.G.IRON INGOT MOULD TO SIZE 20'' X 2500 MM AS PER DRG. NO-OH /1012/153 R1.MATERIAL SPECN:S.G.IRON IS:1865,GRADE:400/18.FIRM SHOULD SUBMIT T.C.FROM NABL ACCREDITED/GOVT. APPROVED LAB FOR BASIC MATERIAL & MECHANICAL PROPERTIES.

SPECN:S.G.IRON IS:1865,GRADE:400/18

DRG. NO-OH /1012/153 R1.

MANUFACTURE OF C.I. INGOT MOULD 175 MM DIA TO MSF DRG.NO. MP/121 R1.

MANUFACTURE OF C.I. INGOT MOULD 175 MM DIA TO MSF DRG.NO. MP/121 R1.

MSF DRG.NO. MP/121 R1

31 INCH C.I. INGOT MOULD AS PER MSF DRG NO.OH 1012/72 R2 (ITEM NO.1 ONLY)

31 INCH C.I. INGOT MOULD AS PER MSF DRG NO.OH 1012/72 R2 (ITEM NO.1 ONLY)

MSF DRG NO OH 1012/72 R2 (ITEM NO.1 ONLY)

"BOTTOM POURING S.G IRON INGOT MOULD TO SIZE 420MM DIA X 218 MM LONG AS PER DRG.NO.LFVD/1000/12/A REV.1. MATERIAL SPECN. SPHEROIDAL CAST IRON IS:1865, GRADE:400/18.FIRM SHOULD SUBMIT T.C FROM NABL ACCREDITED/GOVT.APPROVED LAB ONLY FOR BASIC MATAL & MECHANICAL PROPERTIES. "

MATERIAL SPECN. SPHEROIDAL CAST IRON IS:1865, GRADE:400/18.

LFVD/1000/12/A REV.1

BODY LINING REFRACTORY BRICKS FOR 15 TON ARC FURNACE FOR SET-B OF DRG.NO. 15 ARC/1000/159 R4.

BODY LINING REFRACTORY BRICKS FOR 15 TON ARC FURNACE FOR SET-B OF DRG.NO. 15 ARC/1000/159 R4.

15 ARC/1000/159 R4

BODY LINING BRICKS FOR 20/22 TON EAF AS PER DRG. NO-15ARC/1000/192.

BODY LINING BRICKS FOR 20/22 TON EAF AS PER DRG. NO-15ARC/1000/192.

15ARC/1000/192

LINER REFRACTORIES FOR RADIAL FORGING INGOT MOULD AS PER DRG. NO.LFVD/1000/13/1/R1.

LINER REFRACTORIES FOR RADIAL FORGING INGOT MOULD AS PER DRG. NO.LFVD/1000/13/1/R1.

LFVD/1000/13/1/R1

LINEAR REFRACTORIES FOR INGOT MOULD ( TYPE- A ) AS PER DRG.NO.- LFVD / 1000 / 13 R5.

LINEAR REFRACTORIES FOR INGOT MOULD ( TYPE- A ) AS PER DRG.NO.- LFVD / 1000 / 13 R5.

LFVD / 1000 / 13 R5

LADLE REFRACTORY LINING BRICKS FOR LFVD LADLE 20 TON CAPACITY AS PER DRG.NO.LFVD/1000/30 R7. SET "A" MINI KEY TYPE

LADLE REFRACTORY LINING BRICKS FOR LFVD LADLE 20 TON CAPACITY AS PER DRG.NO.LFVD/1000/30 R7. SET "A" MINI KEY TYPE

LFVD/1000/30 R7