HAMMER MK-2 (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

HAMMER MK-2 (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

EQUILIBRATOR ASSY TO DRG. NO. 1015-000413

EQUILIBRATOR ASSY TO DRG. NO. 1015-000413

DRG. NO. 1015-000413

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

B251-800 IPG INTERNAL PIEZO GUAGE

B251-800 IPG INTERNAL PIEZO GUAGE

PART NO.ISV-529A DC NO:37249-A,DT.08.03.10,SPECN:IA 1169(N),DC NO:35576-A, AIDE MEMOIRE- P/11.NOTE-PAINTING AND PROTECTIVE TREATMENT AS PER DRG.PAINTED "OLIVE GREEN"TO ISC NO.220 OF IS-5-2007(SIXTH REVISION) (AMDT.NO.1)(RE-AFFIRMED 2000)

PART NO.ISV-529A DC NO:37249-A,DT.08.03.10,SPECN:IA 1169(N),DC NO:35576-A, AIDE MEMOIRE- P/11.NOTE-PAINTING AND PROTECTIVE TREATMENT AS PER DRG.PAINTED "OLIVE GREEN"TO ISC NO.220 OF IS-5-2007(SIXTH REVISION) (AMDT.NO.1)(RE-AFFIRMED 2000)

CQA(A)/AMN/2608 PT.NO.ISV 529A DC-37249A DT.08/03/10

• SHEARING AND NOTCHING MACHINE SUITABLE PRESS M/C FOR BENDING, FORMING, EMBOSSING/ENGRAVING OPERATION DRILLING MACHINE ARC/GAS WELDING M/C SPOT WELDING M/C PHOSPHATING FACILITY SPRAY PAINTING FACILITY

• SUITABLE MEASURING FACILITY SUITABLE TESTING FACILITY AS PER RELEVANT SPECIFICATION AND DRAWING

DRG.NO.CQA(A)AMN/2644 PART NO.ISV-530A,DC:37249-A,DT.08.3.10 SPECN:IA-1169(n),DC NO:35576-A,PAINTED"OLIVE GREEN"ISC NO: 220 OF IS:5-2007(6TH REVISION) RE AFFIRMED-2012.

DRG.NO.CQA(A)AMN/2644 PART NO.ISV-530A,DC:37249-A,DT.08.3.10 SPECN:IA-1169(n),DC NO:35576-A,PAINTED"OLIVE GREEN"ISC NO: 220 OF IS:5-2007(6TH REVISION) RE AFFIRMED-2012.

PAPER WASHER GLAZED CALENDERED AMMN TO SPCN. JSS 8135-13- 2014 (REV.NO-3) 0.50MM(0.02") THICK OF SIZE 56 MM OD X 36 MM ID.TO DRAWING NO.ERDL DRG 671 DET 9. .

PAPER WASHER GLAZED CALENDERED AMMN TO SPCN. JSS 8135-13- 2014 (REV.NO-3) 0.50MM(0.02") THICK OF SIZE 56 MM OD X 36 MM ID.TO DRAWING NO.ERDL DRG 671 DET 9. .

DRAWING NO.ERDL DRG 671 DET 9. .

PZM NOZZLE CASTING CUM MACHINING LEFT & RIGHT AS PER DRG.NO.FOR LEFT NOZZLE PZM ERDL DRG.NO. 1040, DET-1 AMENDED ON DT.11-03-15,FOR RIGHT NOZZLE PZM ERDL DRG.NO.1040 ,DET-2 AMENDED ON DT.11-03-15 AND FOR CASTING NOZZLE PZM ERDL DRG.NO. 1040.

PZM NOZZLE CASTING CUM MACHINING LEFT & RIGHT AS PER DRG.NO.FOR LEFT NOZZLE PZM ERDL DRG.NO. 1040, DET-1 AMENDED ON DT.11-03-15,FOR RIGHT NOZZLE PZM ERDL DRG.NO.1040 ,DET-2 AMENDED ON DT.11-03-15 AND FOR CASTING NOZZLE PZM ERDL DRG.NO. 1040.

ERDL. DRG NO.1040 DET-1 & ERDL. DRG. NO. 1040 DET-2

• MSME

• PZM NOZZLE CASTING CUM MACHINING LEFT & RIGHT AS PER DRG.NO.FOR LEFT NOZZLE PZM ERDL DRG.NO. 1040, DET-1 AMENDED ON DT.11-03-15,FOR RIGHT NOZZLE PZM ERDL DRG.NO.1040 ,DET-2 AMENDED ON DT.11-03-15 AND FOR CASTING NOZZLE PZM ERDL DRG.NO. 1040.

PAPER WHITE FINE AMMUNITION TO SPECIFICATION JSS-9310-06- 2016. (D.S. CAT NO. 9310-000007) THICKNESS 0.051 PLUS OR MINUS 0.005 MM AND SIZE 762 X 508 MM.

PAPER WHITE FINE AMMUNITION TO SPECIFICATION JSS-9310-06- 2016. (D.S. CAT NO. 9310-000007) THICKNESS 0.051 PLUS OR MINUS 0.005 MM AND SIZE 762 X 508 MM.

• MSME

• PAPER WHITE FINE AMMUNITION TO SPECIFICATION JSS-9310-06- 2016. (D.S. CAT NO. 9310-000007) THICKNESS 0.051 PLUS OR MINUS 0.005 MM AND SIZE 762 X 508 MM.

PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.

PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.

PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.

• MSME

• PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.

PAPER CORRUGATED AMMUNITION SINGLE FACED COARSE FLUTE WIDTH 26" TO JSS-8135-08-2014, REV.NO.4.

PAPER CORRUGATED AMMUNITION SINGLE FACED COARSE FLUTE WIDTH 26" TO JSS-8135-08-2014, REV.NO.4.

• MSME

• PAPER CORRUGATED AMMUNITION SINGLE FACED COARSE FLUTE WIDTH 26" TO JSS-8135-08-2014, REV.NO.4.

LEAD TUBE FOR CLC-4 SPECIFICATIONIS 404 : 1993 (REAFFIRMED 2019), PART-1.GRADE-1 LEAD PURITY:99.8 % (MIN) DIMENTION:ID:240.2 MM. OD:290.2 MM. THICKNESS VERIATION:0.4 MM. LENGHT OF COIL 4 MTR

LEAD TUBE FOR CLC-4 SPECIFICATIONIS 404 : 1993 (REAFFIRMED 2019), PART-1.GRADE-1 LEAD PURITY:99.8 % (MIN) DIMENTION:ID:240.2 MM. OD:290.2 MM. THICKNESS VERIATION:0.4 MM. LENGHT OF COIL 4 MTR

• MSME

• LEAD TUBE FOR CLC-4 SPECIFICATIONIS 404 : 1993 (REAFFIRMED 2019), PART-1.GRADE-1 LEAD PURITY:99.8 % (MIN) DIMENTION:ID:240.2 MM. OD:290.2 MM. THICKNESS VERIATION:0.4 MM. LENGHT OF COIL 4 MTR

SPECN.NO.AS PER PARTICULAR 1.WIDTH : 25.4MM 2.THICKNESS : 2.35MM 3.Wt/mtr IN gms : 36.5 gms ( MAX.) 4.NO. OF ENDS : 316 +_ 2 GOLDEN THREADS AT CENTER (INCLUDING BOTH LAYERS ) 5.PICKS/CM : 11/12 6.DENIER OF YARN : 840 7.BREAKING LOAD : 1850 KG 8.WEAVE TUBULAR PLAIN 9.ELONGATION : 25% TO 35%

SPECN.NO.AS PER PARTICULAR 1.WIDTH : 25.4MM 2.THICKNESS : 2.35MM 3.Wt/mtr IN gms : 36.5 gms ( MAX.) 4.NO. OF ENDS : 316 +_ 2 GOLDEN THREADS AT CENTER (INCLUDING BOTH LAYERS ) 5.PICKS/CM : 11/12 6.DENIER OF YARN : 840 7.BREAKING LOAD : 1850 KG 8.WEAVE TUBULAR PLAIN 9.ELONGATION : 25% TO 35%

SPECIFICATION NO. ADRDE/SPECN/1985/27(a) ROLL LENGTH 55 MTR.EXCLUDING SAMPLING

SPECIFICATION NO. ADRDE/SPECN/1985/27(a) ROLL LENGTH 55 MTR.EXCLUDING SAMPLING

SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)

SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 100 MTR.INCLUDING SAMPLING

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 100 MTR.INCLUDING SAMPLING

SPECIFICATION NO. : ADRDE/SPECN/68. ROLL LENGTH 90 MTR.EXCLUDING SAMPLING.

SPECIFICATION NO. : ADRDE/SPECN/68. ROLL LENGTH 90 MTR.EXCLUDING SAMPLING.

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 55 MTR. INCLUDING SAMPLING

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 55 MTR. INCLUDING SAMPLING

SPECN-ADRDE/SPCN.2000/54(b)

SPECN-ADRDE/SPCN.2000/54(b)

TAPE NYLON 66, 26mm TUBULAR BS 1850 KG ADRDE/SPECN/2000/54(c)

ADRDE/SPECN/2000/54(c)

TAPE NYLON 66,43 MM.B.S. 9000 N U/D

ADRDE/SPECN/1985/27(b)

• As Per Specification/Drawing

• As Per Specification/Drawing

SPECN.NO:-ADRDE/SPECN/2000/54(b)

SPECN.NO:-ADRDE/SPECN/2000/54(b)

ADRDE/SPCN/2000/54(b)

ADRDE/SPCN/2000/54(b)

SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached. Packing and marking as per schedule No.CIT&C/PMS/65.

SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached. Packing and marking as per schedule No.CIT&C/PMS/65

SPECN.NO. IS:4228-1979

SPECN.NO. IS:4228-1979

SPECIFICATION NO. : IS:9686-1980 PACKING & MARKING: CIT&C/PMS/130 SUITABLY.

SPECIFICATION NO. : IS:9686-1980 PACKING & MARKING: CIT&C/PMS/130 SUITABLY.

TAPE COTTON 19 MM OG SPECIAL

TAPE COTTON 19 MM OG SPECIAL IS : 3255-1979 Except that :- (i) The specified Picks Density is minimum. (ii) The Density of Weft Yarn may be halved and Picks density (minimum) double in case of Needle Loom manufacturing. (iii) In appearance shade, finish & in all other respect not defined in this IS Specn. The material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, Kanpur. (iv) There shall be no presence of starch. (v) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent). (vi) 100% Sampling Testing & Inspection will be resorted to. Sampling plan as per annexure (a) attached. Packing and marking as per schedule CIT&C/PMS/65.

• As per Specification/Drawing

• As per Specification/Drawing

AS PER ADRDE SPCN.NO.ADDE/BP/1(b).

AS PER ADRDE SPCN.NO.ADDE/BP/1(b).

SPECN.NO.JSS:8315-6.

SPECN.NO.JSS:8315-6.

SPECN. NO. Best Trade Quality

SPECN. NO. Best Trade Quality

TAPE NYLON 30 MM O.G. BS 580 KG

SPECIFICATION NO. : ADRDE/SPECN/1993/44(a) ROLL LENGTH 100 MTR. EXCLUDING SAMPLING. Except that : - Shade should be as per approved sample held with QCM/OPF.

• AS PER SPECIFICATION/DRAWING

• AS PER SPECIFICATION/DRAWING

SPCN.: IS:3687-1987

SPCN.: IS:3687-1987

PCB CONTROL MODULE AS PER DRG. NO. 7084.32.03.100

PCB CONTROL MODULE AS PER DRG. NO. 7084.32.03.100

7084.32.03.100

HORIZONTAL GIDANCE POWER SUPPLY AS PER SPECN. NO. 7084.32.06.100

HORIZONTAL GIDANCE POWER SUPPLY AS PER SPECN. NO. 7084.32.06.100

7084.32.06.100

PCB PHASE SENSITIVE RECTIFIER AS PER DRG. NO. 7084.32.02.400-01

PCB PHASE SENSITIVE RECTIFIER AS PER DRG. NO. 7084.32.02.400-01

7084.32.02.400-01

PCB ADAPTER AS PER DRG. NO. 7064.03.03.000

PCB ADAPTER AS PER DRG. NO. 7064.03.03.000

DRG. NO. 7064.03.03.000

PCB ADJUSTMENT BOARD AS PER DRG. NO. 7064.03.01.600

PCB ADJUSTMENT BOARD AS PER DRG. NO. 7064.03.01.600

DRG. NO. 7064.03.01.600

PCB CONTROL MODULE OF SMALL SIZE GYRO AS PER DRG. NO. 7194.03.01.000

PCB CONTROL MODULE OF SMALL SIZE GYRO AS PER DRG. NO. 7194.03.01.000

7194.03.01.000

CONE STEEL TO DRG NO.CIA D2(L)961/E/326,DC NO.34922-A AND OFB DRG. NO. OFB/C/1443 MATERIAL TO SPECN. BS-1449 PT. I 1983 GRADE KHR 43/25 ALTERNATIVELY CONE MAY BE MANUFACTURED BY FORGING METHOD FOR STEEL BAR TO SPECN. BS-970 PT. I :1983 GRADE 070 M20 NOTE :- CONE SHOULD BE SUITABLY OILED AND PACKED

CONE STEEL TO DRG NO.CIA D2(L)961/E/326,DC NO.34922-A AND OFB DRG. NO. OFB/C/1443 MATERIAL TO SPECN. BS-1449 PT. I 1983 GRADE KHR 43/25 ALTERNATIVELY CONE MAY BE MANUFACTURED BY FORGING METHOD FOR STEEL BAR TO SPECN. BS-970 PT. I :1983 GRADE 070 M20 NOTE :- CONE SHOULD BE SUITABLY OILED AND PACKED

OFB DRG. NO. OFB/C/1443

SELF EXTINGUISHING TYPE AND BULK/APPARENT DENSITY 15/20 KG PER CUBIC METER TO SPECN: IS-4671-1984(FIRST REVISION) REAFFIRMED 1995 SIZE:265MMx 146MMx 12(-) 1 MM

SELF EXTINGUISHING TYPE AND BULK/APPARENT DENSITY 15/20 KG PER CUBIC METER TO SPECN: IS-4671-1984(FIRST REVISION) REAFFIRMED 1995 SIZE:265MMx 146MMx 12(-) 1 MM

HOSE TO DRG. NO. AK-630 SB-114-17 IN FINISHED CONDITION

AS PER DRAWING

AK-630 SB 114-17

• AS PER ATTACHMENT

• AS PER ATTACHMENT

HOSE TO DRG. NO. AK-630 SB 114-16 IN FINISHED CONDITION

AS PER DRAWING

AK-630 SB 114-16

• As per attachment

• As per attachment

HOSE TO DRG. NO. AK-630 SB 114-14 IN FINISHED CONDITION

AS PER DRAWING

AK-630 SB-114-14

• AS PER ATTACHMENT

• AS PER ATTACHMENT

AS PER DRG. & SPECIFICATION

AS PER DRG. & SPECIFICATION

• As per attachment

• as per attachment

BELLEVILLE SPRING DRG.NO.AK-630.120-4

AS PER DRG

AK 630 120-4

COLLECTOR/MANIFOLD ASSY. AK-630 SB 108 SB

AS PER DRAWING

• As per attached file

• As per attached file

RECEIVER TO DRG, NO. CTM-0108/1 TO CTM-0108/6

AS PER DRAWING

CTM-0108/1 TO CTM-0108/6

SURFACE TREATMENT OPERATION VIZ: NICKEL PLATING (WITH COPPER - UNDER COAT ) TO SPEC BS: 1224-1970 FOLLOWED BY ELECTRO PHORETIC LAQUERING WITH BLACKISH TINGE WITH SOLID CONTENT 9.9 TO 13% AND PH: 5.2 TO 5.6. THICKNESS OF LAQUER 5 TO 6 MICRON ON COMP PB1, PB3, PB6, PB7, PB9, PB10, PB 15, PB23, PB 32, PB39, PB41 & CTM 0099

SURFACE TREATMENT OPERATION VIZ: NICKEL PLATING (WITH COPPER - UNDER COAT ) TO SPEC BS: 1224-1970 FOLLOWED BY ELECTRO PHORETIC LAQUERING WITH BLACKISH TINGE WITH SOLID CONTENT 9.9 TO 13% AND PH: 5.2 TO 5.6. THICKNESS OF LAQUER 5 TO 6 MICRON

• AS PER ATTACHMENT

• AS PER ATTACHMENT

MAGAZINE SUB ASSY. TO DRG. NO. CTM-0112 IN F/C

AS PER DRAWING

CTM-0112

TORSION SPRING TO DRG. NO. CTM-0114 IN F/C

AS PER DRG

CTM-0114

HAMMER TO DRG. NO. CTM-0110/1 TO CTM-0110/6 FOR MODIFIED PISTOL

AS PER DRAWING

CTM-0110 TO CTM-0110/6

SET OF STOCK RT & LT DRG. NO. CTM-0118 & CTM-0117

AS PER DRAWING

CTM-0117 & CTM-0118

MAGAZINE SUB ASSY. TO DRG. NO. CTM-0112 IN F/C

AS PER DRAWING

CTM-0112

RADIATOR & COOLERS 765-03-K6 CONSISTS OF COOLER OIL VEHICULAR 765-03-Cb161, WATER RADIATOR 765-03-Cb178 & COOLER OIL VEHICULAR 765-03-Cb162

765-03-K6

LFG ORDNANCE COMPONENTS AS PER ANNEXURE "G"

LFG ORDNANCE COMPONENTS AS PER ANNEXURE "G"

SPRING FOR LFG ORDNANCE AS PER ANNEXURE "C"

SPRING FOR LFG ORDNANCE AS PER ANNEXURE "C"

STOCK BUTT TO DRG.NO.: 29 P 0038*2 required for 0.315" Sporting Rifle

AS PER DRG.NO.: 29 P 0038*2 required for 0.315" Sporting Rifle

29 P 0038*2

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

CONVERSION OF BOLT BREECH FROM FORGING TO TEND DRG.NO 2369 required for 0.315" Sporting Rifle

AS PER TEND DRG.NO 2369 required for 0.315" Sporting Rifle

TEND 2369

SPRING MAIN TO DRG. NO.32-0106 MATERIAL SPRING STEEL, Gr- 4, IS: 4454 (Pt-1)-81

SPRING MAIN TO DRG. NO.32-0106 MATERIAL SPRING STEEL, Gr- 4, IS: 4454 (Pt-1)-81

32-0106

TRIGGER TO DRG. NO. 32-0701 MK-III ALT VERSION 2 MATERIAL: BS 970 Pt.1: 1983 GD. 070 M-55 (BS 970 EN-9)/ALT.MTL.(I.C.)BS3146 PT.-1,1974 TYPE CLASS-8 ALT. MATERIAL FOR MIM COMPONENTS:MIM 4650. C:0.3-0.6%, NI:1.5-2.5%,Cr-0.5% MAX.,Si-0.5%, Mo:0.5% MAX.,Mn:0.3%,

TRIGGER TO DRG. NO. 32-0701 MK-III ALT VERSION 2 MATERIAL: BS 970 Pt.1: 1983 GD. 070 M-55 (BS 970 EN-9)/ALT.MTL.(I.C.)BS3146 PT.-1,1974 TYPE CLASS-8 ALT. MATERIAL FOR MIM COMPONENTS:MIM 4650. C:0.3-0.6%, NI:1.5-2.5%,Cr-0.5% MAX.,Si-0.5%, Mo:0.5% MAX.,Mn:0.3%,

32-0701

HAMMER TO DRG. NO. 32-0601 MK-III,MATERIAL BS 970 PT I 1983 GD:070 M-55(B.S 970 EN-9) ALT.MATERIAL: FROM I.C ROUTE I.C DRG NO.SK-5377R BS 3146 Pt.1-1974. TYPE CLASS-12 Gr.A.

HAMMER TO DRG. NO. 32-0601 MK-III,MATERIAL BS 970 PT I 1983 GD:070 M-55(B.S 970 EN-9) ALT.MATERIAL: FROM I.C ROUTE I.C DRG NO.SK-5377R BS 3146 Pt.1-1974. TYPE CLASS-12 Gr.A.

32-0601

PLATE BODY TO DRG. NO. 32-0501 MK-III MATERIAL:-BS 970 Pt.1: 1983 Gd. 070 M-55 (BS 970 EN-9), FINISH:-ELECTROSTATIC POWDER COATING AFTER ASSY. ALT MATERIAL FROM IC ROUTE:-BS 3146 PT.1 1974 TYPE CLASS-8.

PLATE BODY TO DRG. NO. 32-0501 MK-III MATERIAL:-BS 970 Pt.1: 1983 Gd. 070 M-55 (BS 970 EN-9), FINISH:-ELECTROSTATIC POWDER COATING AFTER ASSY. ALT MATERIAL FROM IC ROUTE:-BS 3146 PT.1 1974 TYPE CLASS-8.

32-0501

AXIS CYLINDER DRG.NO-PH-3/2 & FGK DRG NO.32-0302(IN FINISH C SPECN BS 970 PT.1:1983 GRADE 080 M40

AXIS CYLINDER DRG.NO-PH-3/2 & FGK DRG NO.32-0302(IN FINISH C SPECN BS 970 PT.1:1983 GRADE 080 M40

32-0302

BODY (IC) TO DRG. NO. SK-01397 MATERIAL:- B.S 3146 PART-1: 1974 CLASS 5A, HEAT TREATMENT-ANNEALING. (TEST PEACE IS TO BE - TESTED FROM ONE CASTING DULY HARDENED AND TEMPERED FROM EACH CAST FOR MECHANICAL PROPERTIES STIPULATED IN THE SPECIFICATI

BODY (IC) TO DRG. NO. SK-01397 MATERIAL:- B.S 3146 PART-1: 1974 CLASS 5A, HEAT TREATMENT-ANNEALING. (TEST PEACE IS TO BE - TESTED FROM ONE CASTING DULY HARDENED AND TEMPERED FROM EACH CAST FOR MECHANICAL PROPERTIES STIPULATED IN THE SPECIFICATI

SK-01397

INSULATOR LOWER DRG.NO.2A26-02-269

INSULATOR LOWER DRG.NO.2A26-02-269

2A26-02-269

INSULATOR UPPER DRG.NO.2A26-02-268

INSULATOR UPPER DRG.NO.2A26-02-268

2A26-02-268

BUSHING DRG.NO.2A26-02-154

BUSHING DRG.NO.2A26-02-154

2A26-02-154

LOCK DRG.NO.2A26-02-128

LOCK DRG.NO.2A26-02-128

2A26-02-128

PLUG DRG.NO.2A26-02-125

PLUG DRG.NO.2A26-02-125

2A26-02-125

RING DRG NO: 2A26-02-122.

RING DRG NO: 2A26-02-122.

2A26-02-122.

RING SPRING TO DRG.NO.A51203-175.

RING SPRING TO DRG.NO.A51203-175.

A51203-175.

SPRING TO DRG NO A51230-199

SPRING TO DRG NO A51230-199

A51230-199

SPRING TO DRG NO A51230-154

SPRING TO DRG NO A51230-154

A51230-154

SPRING TO DRG NO A51230-109

SPRING TO DRG NO A51230-109

A51230-109

SPRING TO DRG NO.A-51230-108.

SPRING TO DRG NO.A-51230-108.

A-51230-108.

SPRING TO DRG NO A51230-41

SPRING TO DRG NO A51230-41

A51230-41

SPRING TO DRG NO A51230-16

SPRING TO DRG NO A51230-16

A51230-16

SPRING TO DRG NO A51230-13

SPRING TO DRG NO A51230-13

A51230-13