SCREW LF NO 7440206614

SCREW LF NO 7440206614

AL8914221-05

POST LF NO 7440206203

POST LF NO 7440206203

70640100013

STOP LF NO 7440206181

STOP LF NO 7440206181

70640101114

BRACKET LF NO 7440206177

BRACKET LF NO 7440206177

70640101301

RING DRG NO AL8247267 LF NO 7440206008

RING DRG NO AL8247267 LF NO 7440206008

CRAMP OR CLAMP LF NO 7440205783

CRAMP OR CLAMP LF NO 7440205783

AL8668170

GASKET FOR GYRO STABILIZER TO DRG NO IUMK.754142.011 (LF 7440202661)

GASKET FOR GYRO STABILIZER TO DRG NO IUMK.754142.011 (LF 7440202661)

BUSHING FOR GYRO STABILIZER TO DRG NO AL8.220.950 (LF 7440202657)

BUSHING FOR GYRO STABILIZER TO DRG NO AL8.220.950 (LF 7440202657)

SPRING LF NO 7440200913

SPRING LF NO 7440200913

AL8383508

AXLE LF NO 7440200900

AXLE LF NO 7440200900

AL8314296

• MECHANICAL COMPONENT

• MECHANICAL COMPONENT

BUSHING LF NO 7440200198

BUSHING LF NO 7440200198

AL7860506

RING TO AUTOMATIC BLOCK 9S517-1S TO DRG NO BG29.033 (LF 7440101214)

RING TO AUTOMATIC BLOCK 9S517-1S TO DRG NO BG29.033 (LF 7440101214)

T.E. 190049DLFO CLIP CARTRIDGE

T.E. 190049DLFO CLIP CARTRIDGE

CORD. NYLON 1785 N B.L. WHITE

SPECN NO:JSS:4020-9-2013, ( Required Roll Length 337 M excluding test sample ) Except that:- in appearance and all other respects not defined in this specn, the material shall conform to the sealed sample held in the costody the controller, CQAT&C, KANPUR (iii)Packing and marking Sampling Plan & Criteria of conformity As per relevant clause of specn. (iv)Pre inspection, warranty and Advance sample Clause as per specification.

• As Per Specification/Drawing

• As Per Specification/Drawing

9999909313 DESIGN AND MANUFACTURE MILLING FIXTURE FOR MACHINING OF ECCENTRIC BUSHING DRG NO 2A46 21 32

DESIGN AND MANUFACTURE MILLING FIXTURE FOR MACHINING OF ECCENTRIC BUSHING,DRG.NO.2A46.21-32.

7119033985 SCREW STOPPER TO DRG NO 175 66 117 FOR DISTRIBUTION COCK ASSEMBLY T 90

SCREW STOPPER TO DRG.NO.175.66.117 FOR DISTRIBUTION COCK ASSEMBLY,T-90

7119033992 VALVE ASSEMBLY TO DRG NO 188 66 020CBCB FOR DISTRIBUTION COCK ASSEMBLY

VALVE ASSEMBLY TO DRG.NO.188.66.020CBCB FOR DISTRIBUTION COCK ASSEMBLY,T-90

7119033984 PLUG TO DRG.NO.172.66.237 FOR DISTRIBUTION COCK ASSEMBLY

PLUG TO DRG.NO.172.66.237 FOR DISTRIBUTION COCK ASSEMBLY,T-90

2519139573 TESTING ARRANGEMENT FOR WATER

TESTING ARRANGEMENT FOR WATER FLOW OF BILGE PUMP REAR AS PER DRG.NO.F-675-38-CD 108-2 & SCOPE OF WORK.

2519139574 TESTING ARRANGEMENT FOR WATER

TESTING ARRANGEMENT FOR WATER FLOW OF BILGE PUMP FRONT AS PE R DRG.NO.F-54-83-78CD A-1&SCOP E OF WORK.

8022250162 MACHINING OF IMPELLER TO DRG NO 54 83 005 1A

8022250162 MACHINING OF IMPELLER TO DRG NO 54 83 005 1A

DRG NO-54-83-005-1A

M/CING OF RACK EXT. AND INT.

M/CING OF RACK EXT. AND INT.

AUTO SEAR FOR JVPC 5.56MM THROUGH MIM ROUTE DRG.NO.0204 03 02 02 18 016 00DC

AUTO SEAR FOR JVPC 5.56MM THROUGH MIM ROUTE DRG.NO.0204 03 02 02 18 016 00DC

0204 03 02 02 18 016 00DC

• MIM ROUTE

• CHEMICAL AND MECHANICAL PROPERTIES AS PER STD. GIVEN DRAWING.
• DIMENSIONAL INSPECTION, FOR ALL DIMENSIONS GIVEN IN THE DRAWING AND OTHER PARAMETER WHICH ARE MENTIONED IN RELEVANT DRAWING.

Sear for JVPC 5.56MM through MIM route DRG.NO.0204 03 02 02 18 014 00DE 014

Sear for JVPC 5.56MM through MIM route DRG.NO.0204 03 02 02 18 014 00DE 014

0204 03 02 02 18 014 00DE

CASE, ARTILLERY AND MAP BOARDS, MK 2 AS PER DRG.NO.: O.S.30986(17 SHEETS)

CASE, ARTILLERY AND MAP BOARDS, MK 2 AS PER DRG.NO.: O.S.30986(17 SHEETS)

DRG.NO.: O.S.30986(17 SHEETS)

CASE CANVAS TO DRG NO.MCT-1682/1 MCT-1682/1 NOTE:EACH CANVAS CASE WILL BE SUPPLIED IN GOOD QUALITY OF POLYTHENE BAG (INDIVIDULLY)

CASE CANVAS TO DRG NO.MCT-1682/1 MCT-1682/1 NOTE:EACH CANVAS CASE WILL BE SUPPLIED IN GOOD QUALITY OF POLYTHENE BAG (INDIVIDULLY)

MCT-1682/1

CASE CARRYING FRP FOR SIGHT NIGHT VISION PASSIVE 5.56MM RIFLE(INSAS)101A DRG.NO. MCT-1678/2 COMPLETE WITH DRG MCT-1679/1,MCT-1680/1MCT1637/1,MCT-1646/1 MCT-2007.MCT-2008,MCT-2546/1,MCT-2548/1,MCT- 1644/1,1636/1,1617/1,MCT-1369,1370,1375,1376 MCT-1380,& MCT-1641/1.

CASE CARRYING FRP FOR SIGHT NIGHT VISION PASSIVE 5.56MM RIFLE(INSAS)101A DRG.NO. MCT-1678/2 COMPLETE WITH DRG MCT-1679/1,MCT-1680/1MCT1637/1,MCT-1646/1 MCT-2007.MCT-2008,MCT-2546/1,MCT-2548/1,MCT- 1644/1,1636/1,1617/1,MCT-1369,1370,1375,1376 MCT-1380,& MCT-1641/1.

CASE CARRYING FRP FOR SIGHT NIGHT VISION PASSIVE 5.56MM RIFLE(INSAS)101A DRG.NO. MCT-1678/2 COMPLETE WITH DRG MCT-1679/1,MCT-1680/1MCT1637/1,MCT-1646/1 MCT-2007.MCT-2008,MCT-2546/1,MCT-2548/1,MCT- 1644/1,1636/1,1617/1,MCT-1369,1370,1375,1376 MCT-138

ENGRAVING OF SCALE ARTILLERY AS PER DRG. NO.CIA (OS) 564. BLANK WILL BE SUPPLIED BY OFD (FIRM SHOULD SUPPLY THE ITEM WITH PROPER PACKING TO AVOID SCRATCHES)

ENGRAVING OF SCALE ARTILLERY AS PER DRG. NO.CIA (OS) 564. BLANK WILL BE SUPPLIED BY OFD (FIRM SHOULD SUPPLY THE ITEM WITH PROPER PACKING TO AVOID SCRATCHES)

video cable assy. for CTI-T-72 YO DRG.NO. 096704000000000

video cable assy. for CTI-T-72 YO DRG.NO. 096704000000000

AS PER DRG. AND SPECN

AS PER DRG. AND SPECN

NETTING POLYESTER ROUND MESH UD 132CM

SPECIFICATION : 1. WIDTH - 132 + - 2 CM 2. THICKNESS (MAX.)-0.45mm AT 200g/Sq.Cm. 3. MASS (MAX.) –107 gm /Sq. METERE 4. BS 5X20 Cm STRIP - WARP -35 Kg. MIN.,WEFT-16Kg.MIN. 5. NO.OF MESH/Sq. INCH -140 6. TEARING STRENGTH IN BOTH DIRECTION -3.2 kg. MIN. 7. BURSTING STRENGTH – 11 Kg. MIN. 8. ELONGATION AT BREAK:- a. LENGTH DIRECTION -40% (MAX.) b. WIDTH DIRECTION -100% (MAX.)

LANEYARD WITH CLIP HOOK TO DRG.NO.AMG 68763/1015-001845

LANEYARD WITH CLIP HOOK TO DRG.NO.AMG 68763/1015-001845

0.32" PISTOL BOX DRG. NO. M-9881-B IN FINISHED CONDITION. NOTE:- FIRM MAY GIVE ALT. OFFER OF THE BOX WITH STEEL LOCK(PLATED GOLDEN COLOUR) INSTEAD OF BRASS LOCK REMAINING OTHER PARAMETER UNCHANGED

0.32" PISTOL BOX DRG. NO. M-9881-B IN FINISHED CONDITION. NOTE:- FIRM MAY GIVE ALT. OFFER OF THE BOX WITH STEEL LOCK(PLATED GOLDEN COLOUR) INSTEAD OF BRASS LOCK REMAINING OTHER PARAMETER UNCHANGED

FORGING OF PISTON EXTENSION AS PER RFI SK.NO.6422*2-S FOR RIFLE 5.56MM INSAS THROUGH CONVERSION ROUTE.

FORGING OF PISTON EXTENSION AS PER RFI SK.NO.6422*2-S FOR RIFLE 5.56MM INSAS THROUGH CONVERSION ROUTE.

AS PER RFI SK.NO.6422*2-S

TRIGGER FORGING AS PER RFISK.NO.7057*-S FOR RIFLE 5.56MM INSAS

TRIGGER FORGING AS PER RFISK.NO.7057*-S FOR RIFLE 5.56MM INSAS

RFISK.NO.7057*-S

Steel Blank of Cylinder Gas To Drg. No. SKM-889* without heat treatment (Steel Forging SKM-306*6 LF No. 0144079003 to be issued by SAF against B/G).

Steel Blank of Cylinder Gas To Drg. No. SKM-889* without heat treatment (Steel Forging SKM-306*6 LF No. 0144079003 to be issued by SAF against B/G).

SKM-889*

• Forging/Machining

• Chemical & Mechanical Properties as per std. given drawing
• Dimensional inspection, for all dimensions given in the drawing and other parameters which are mentioned in the relevant drawing

FABRICATION OF OVERALL DRILL MP. SWO PART II No. 60238.

FABRICATION OF OVERALL DRILL MP. SWO PART II No. 60238. SPECIFICATION: 1) DIMENSION: AS PER SPECN. NO. IND/TC/4403(L) & SCH. NO. CQA(T&C)/TC-15/8(d) 2) BASIC MATERIAL: CLOTH DRILL COTTON DARK GREY AS PER V.NO. 3 OF IS:177 3) MAKE AND SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) DRAWING AND SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

ST. BLANK OF RECEIVER PLATE LEFT & RIGHT TO DRG. SKM-960* WITH FIRM'S MAT. THE PROFILE & REF HOLES (SHOULDER LOCKING HOLE DIA 13 .39 (+_0.02) & BUSH MOUNTING FRONT HOLE DIA 18.025 (+_0.02) TO BE DONE SIMULT IN BOTH PLATES KEPT TOGETHER ONE ABOVE AND THER & NO. TO MAKE SET DRG. SKM 884*2 & SKM-884/1*3 ENCL

AS PER DRG.

SKM-960*

• AS PER ENCLOSED

• AS PER ENCLOSED

ST. BLANK OF RECEIVER PLATE LEFT & RIGHT TO DRG. SKM-960* WITH FIRM'S MAT. THE PROFILE & REF HOLES (SHOULDER LOCKING HOLE DIA 13 .39 (+_0.02) & BUSH MOUNTING FRONT HOLE DIA 18.025 (+_0.02) TO BE DONE SIMULT IN BOTH PLATES KEPT TOGETHER ONE ABOVE AND THER & NO. TO MAKE SET DRG. SKM 884*2 & SKM-884/1*3 ENCL

AS PER DRG.

SKM-960*

• AS PER ENCLOSED

• AS PER ENCLOSED

UPPER HAND GUARD ASSY AS PER DRG NO K 2050 ALT STR 2 WITH FIRMS MATERIAL FOR TRICHY ASSAULT RIFLE

UPPER HAND GUARD ASSY AS PER DRG NO K 2050 ALT STR 2 WITH FIRMS MATERIAL FOR TRICHY ASSAULT RIFLE

K 2050 ALT STR 2

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

COMPOSITE ARMOUR (RHS) & (LHS) AS PER DRG NO. 645-15-1-1 TO 15/F

COMPOSITE ARMOUR (RHS) & (LHS) AS PER DRG NO. 645-15-1-1 TO 15/F and SPECIFICATION NO. OFPM/R&D/SP/COMPOSITE - ARMOUR/07 DT. 16.03.2007 Amendment No.: 04 Dt. 02.03.2019

645-15-1-1 TO 15/F

• AS PER SPECIFICATION

• AS PER SPECIFICATION & QAP

Cobalt Powder as Per CQAM 58 Specification

As per enclosed Monitoring Instructions No: HAPP/QA/SC/G/026, Issue No. 01, Rev. No.04, Date of Issue 04.07.2019 (Annexure A).

9927093105 SHIELDING BRAID (PML)- 2X4 SHIELDING BRAID TYPE-PML- 2X 4 AS PER SPECIFICATION NO;OLF/AL /SHIELD/01/MOD

9927093105 SHIELDING BRAID (PML)- 2X4 SHIELDING BRAID TYPE-PML- 2X 4 AS PER SPECIFICATION NO;OLF/AL /SHIELD/01/MOD

9001121786 A SET OF WIRES CONSISTING OF A SET OF WIRES CONS.OF A) PTFE INSU.SILVER PLATED COPPER CON DT. SIZE AWG 24/7/32 TYPE ET, 250VAC GRADE, WHITE/RED/BLACK B)PTFE INSU. SILVER PLATED CO PPER CONDU. SIZE AWG26/7/34 TY PE E, 600VAC C) PTFE INSU. SIL. PLA. COP. CONDT. WG26/7 /34 TYPE E, 600VAC, 2 CR.TWISTED & OVERALL PTFE J C OD 2.5MM

9001121786 A SET OF WIRES CONSISTING OF A SET OF WIRES CONS.OF A) PTFE INSU.SILVER PLATED COPPER CON DT. SIZE AWG 24/7/32 TYPE ET, 250VAC GRADE, WHITE/RED/BLACK B)PTFE INSU. SILVER PLATED CO PPER CONDU. SIZE AWG26/7/34 TY PE E, 600VAC C) PTFE INSU. SIL. PLA. COP. CONDT. WG26/7 /34 TYPE E, 600VAC, 2 CR.TWISTED & OVERALL PTFE J C OD 2.5MM

9001121633 SHRINKABLE SLEEVE 8.0 X 0.5 MM SHRINKABLE SLEEVE 8.0 X 0.5 MM AS PER SPECN. NO. OLF/A-I/HSS/CTI-T-72

9001121633 SHRINKABLE SLEEVE 8.0 X 0.5 MM SHRINKABLE SLEEVE 8.0 X 0.5 MM AS PER SPECN. NO. OLF/A-I/HSS/CTI-T-72

9001121337 SHRINKABLE SLEEVE 6 X 0.5 MM HEAT SHRINKABLE SLEEVE 6 X 0.5 MM AS PER SPECN. NO. OLF/A-1/HSS/CTI/T-72/14

9001121337 SHRINKABLE SLEEVE 6 X 0.5 MM HEAT SHRINKABLE SLEEVE 6 X 0.5 MM AS PER SPECN. NO. OLF/A-1/HSS/CTI/T-72/14

9001121336 SHRINKABLE SLEEVE 1 X 0.2 MM HEAT SHRINKABLE SLEEVE 1 X 0. 2 MM AS PER SPECN. NO. OLF/A-1/HSS/CTI/T-72/14

9001121336 SHRINKABLE SLEEVE 1 X 0.2 MM HEAT SHRINKABLE SLEEVE 1 X 0. 2 MM AS PER SPECN. NO. OLF/A-1/HSS/CTI/T-72/14

9001121335 HEAT SHRINKABLE SLEEVE 2 X 0.2 SLEEVE (HEAT SHRINKABLE SLEEVE )-NOMINAL SIZE-2 X 0.2 MM AS PER SPECN. NO. OLF/A-1/HSS /CTI/T-72/14

9001121335 HEAT SHRINKABLE SLEEVE 2 X 0.2 SLEEVE (HEAT SHRINKABLE SLEEVE )-NOMINAL SIZE-2 X 0.2 MM AS PER SPECN. NO. OLF/A-1/HSS /CTI/T-72/14

9001120436 SLEEVE(HEAT SHRINKABLE)-6X0.25 SLEEVE (HEAT SHRINKABLE SLEEVE )-NOMINAL SIZE-6X0.25 MM AS PER SPECN. NO: OLF/AII/AL/1 1/HSS ATTACHED

9001120436 SLEEVE(HEAT SHRINKABLE)-6X0.25 SLEEVE (HEAT SHRINKABLE SLEEVE )-NOMINAL SIZE-6X0.25 MM AS PER SPECN. NO: OLF/AII/AL/1 1/HSS ATTACHED

MGTF-0.35MM Drg No.TU16.505.185-71 WIRE MGTF-0.35MM AS PER SPECN. NO.TU16.505.185-71

MGTF-0.35MM Drg No.TU16.505.185-71 WIRE MGTF-0.35MM AS PER SPECN. NO.TU16.505.185-71

St. Sheet 1.00X1250X2500MM DD quality. (cold rolled) to specification IS:513-(latest issue).

St. Sheet 1.00X1250X2500MM DD quality. (cold rolled) to specification IS:513-(latest issue).

SPECN-AS PER PARTICULARS. WIDTH : 26.5+-0.5 MM, THICKNESS :0.42MM(MAX) WEIGHT/METER :5.2 GM(MAX) BREAKING STRENGTH :150 KG(MIN) HEAT SETTING :PROPER HEAT SETTING IS REQUIRED WEAVE :2X2 BROKEN TWILL(2 ENDS WORKING AS ONE) TOTAL NO.OF ENDS :228 PICKS/CM :24 DENIER OF YARN :(a)ENDS:153,(b)PICKS :150 T.P.M.(RANGE) :(a)WARP:140-215,,(b)WEFT :165-215 EXTENSION AT BREAK :20-30%

SPECN-AS PER PARTICULARS. WIDTH : 26.5+-0.5 MM, THICKNESS :0.42MM(MAX) WEIGHT/METER :5.2 GM(MAX) BREAKING STRENGTH :150 KG(MIN) HEAT SETTING :PROPER HEAT SETTING IS REQUIRED WEAVE :2X2 BROKEN TWILL(2 ENDS WORKING AS ONE) TOTAL NO.OF ENDS :228 PICKS/CM :24 DENIER OF YARN :(a)ENDS:153,(b)PICKS :150 T.P.M.(RANGE) :(a)WARP:140-215,,(b)WEFT :165-215 EXTENSION AT BREAK :20-30%

Dust Cover Pinion

Dust Cover Pinion

312 2621 063

Oil Seal (IPL - AGB/84) Drg No 2574 2820 7802

Oil Seal (IPL - AGB/84) Drg No 2574 2820 7802

2574 2820 7802

AGB Rear Oil Seal 2574 2820 7803 NR (IPL-AGB/61)

AGB Rear Oil Seal 2574 2820 7803 NR (IPL-AGB/61)

2574 2820 7803

Coller Nut / Hex Nut M35x1.5

Coller Nut / Hex Nut M35x1.5

327 3530 272 A1

Dif Spider 24 Dia

Dif Spider 24 Dia

321 3530 220

Hex Bolt M 14x1x30

Hex Bolt M 14x1x30

323 9900 101

Taper Roller Bearing (31309)

Taper Roller Bearing (31309)

2604 3530 3102

Dust Cover (Press Fit) Part No 2732 3530 8201 b

Dust Cover (Press Fit) Part No 2732 3530 8201 b

2732 3530 8201

Assy Tie Rod Part No X 261433800103

Assy Tie Rod Part No X 261433800103

X 2614 3380 0103

Cyl. Roller Bearing (JC 8005)

Cyl. Roller Bearing (JC 8005)

2604 3530 3104

Cyl. Roller Bearing 2573 3530 3102 ABC NU307ENW with ST-Cage

Cyl. Roller Bearing 2573 3530 3102 ABC NU307ENW with ST-Cage

2573 3530 3102

Taper Roller Bearing (31312L)

Taper Roller Bearing (31312L)

2573 3530 3108

Taper Roller Bearing (30309)

Taper Roller Bearing (30309)

2507 2630 3101

Taper Roller Bearing Timken (32212)

Taper Roller Bearing Timken (32212)

0019812405

Taper Roller Bearing (30214)

Taper Roller Bearing (30214)

2060 3310 3001

Taper Roller Bearing Type (32211)

Taper Roller Bearing Type (32211)

2612 3530 3101

Taper Roller Bearing (30308) (GBS40 Gear Box)

Taper Roller Bearing (30308) (GBS40 Gear Box)

2505 2630 3104

Forg 4th Speed Gear On Main Shaft LPTA BS-III Vehicle Drg No 2691 2620 5421 3

Forg 4th Speed Gear On Main Shaft LPTA BS-III Vehicle Drg No 2691 2620 5421 3

Forging 2nd Speed Gear Main Shaft LPTA BS-III Vehicle Drg No 2691 2620 0416 3 (R3)

Forging 2nd Speed Gear Main Shaft LPTA BS-III Vehicle Drg No 2691 2620 0416 3 (R3)

2691 2620 0416 3 R3

3rd Speed Counter Shaft (Forging) LPTA-715 Vehilce Part No / Drg No 2691 2630 5424 3

3rd Speed Counter Shaft (Forging) LPTA-715 Vehilce Part No / Drg No 2691 2630 5424 3

2691 2630 5424 3

Forging for 4th Speed Gear on Counter Shaft BS-III LPTA 715 Part No / Drg No 2691 2630 5428 3 (R)

Forging for 4th Speed Gear on Counter Shaft BS-III LPTA 715 Part No / Drg No 2691 2630 5428 3 (R)

Forg 3rd Speed Gear On Main Shaft LPTA BS-III Vehicle Drg No 2691 2620 5414 3

Forg 3rd Speed Gear On Main Shaft LPTA BS-III Vehicle Drg No 2691 2620 5414 3

2691 2620 5414 3

Forging for Reverse Idler Gear LPTA 715 BS-III Part No 2691 2635 5407 3 (R1)

Forging for Reverse Idler Gear LPTA 715 BS-III Part No 2691 2635 5407 3 (R1)

2691 2635 5407 3 R1

Forging for Hub L A (Lug Version) 2574 3345 5102 50

Forging for Hub L A (Lug Version) 2574 3345 5102 50

2574 3345 5102 50

Forging for Steering Arm BS-III, LPTA 715, Part No / Drg No 2154 3385 600 3

Forging for Steering Arm BS-III, LPTA 715, Part No / Drg No 2154 3385 600 3

2154 3385 6003 3

Foring for King Pin Upper Part No 2574 3325 5102 3 R2

Foring for King Pin Upper Part No 2574 3325 5102 3 R2

2574 3325 5102 3 R2

Foring for King Pin Lower 340 332 1306 3 (R2)

Foring for King Pin Lower 340 332 1306 3 (R2)

340 332 1306 3 R2

Forging for Flange Axle Housing (Axle Housing) Drg No 2604 3510 5102 3 (R1)

Forging for Flange Axle Housing (Axle Housing) Drg No 2604 3510 5102 3 (R1)

2604 3510 5102 3 R1