LEAD TUBE FOR CLC-3,SPECIFICATION IS 404 : 1993 (REAFFIRMED 2019),PART-1,GRADE-1 PURITY:NOT LESS THAN 99.8%,OD:26.0 (0.2)MM & ID:20.5 ( 0.2)MM LENGTH:820 MM,THICKNESS VARIATION 0.4 MM

LEAD TUBE FOR CLC-3,SPECIFICATION IS 404 : 1993 (REAFFIRMED 2019),PART-1,GRADE-1 PURITY:NOT LESS THAN 99.8%,OD:26.0 (0.2)MM & ID:20.5 ( 0.2)MM LENGTH:820 MM,THICKNESS VARIATION 0.4 MM

• MSME

• LEAD TUBE FOR CLC-3,SPECIFICATION IS 404 : 1993 (REAFFIRMED 2019),PART-1,GRADE-1 PURITY:NOT LESS THAN 99.8%,OD:26.0 (0.2)MM & ID:20.5 ( 0.2)MM LENGTH:820 MM,THICKNESS VARIATION 0.4 MM

FABRIC NYLON 48 + - 2 GMS SAND 92 CMS

SPECN:ADRDE/specn/2002/56(b) variety NO.2

FABRIC NYLON 48 + -2 GMS ORANGE 95 CMS

SPECN:ADRDE/specn./2002/56(b) variety NO.2

FABRIC NYLON 48 + -2 GMS OG 95 CMS

SPECN:ADRDE/specn/2002/56(b) variety NO.2

FABRIC NYLON 48 + - 2 GMS U/D 95 CMS

SPECN:ADRDE/SPECN./2002/56(b)VARIETY NO.2

DRG.NO.: ADRDE/1359(a) DRD/25/98.

DRG.NO.: ADRDE/1359(a) DRD/25/98.

MBEU/7074 PA -- HARDSHELL CONTAINER FOR JAGUAR PILOT PARA.

DRG. NO. ADRDE/1454-00(b)

DRG. NO. ADRDE/1454-00(b)

• AS PER SPECIFICATION/DRAWING

• AS PER SPECIFICATION/DRAWING

Net Fabric Polyester 76 Gms. 20 Kgf BS For Width 120 cms +2 -0 cm excluding selvedge

SPEC NO. ADRDE/QMS/TDTM/F/2009/03(a), DT. 17-05-2021.

• As per Specification/Drawing

• As per Specification/Drawing

DRG.NO.ADRDE/1356.

DRG.NO.ADRDE/1356.

TAPING FABRIC WIDTH 50 MM

Appendix " E" of Specn CQAE/1940/1548/g

COATED FABRIC FOR BUOYANCY TUBE 130 CM WIDTH (MIN)

APPENDIX "A, B & C" AND CLAUSE 6.1 OF SPECN CQAE/1940/1548/g

COATED FABRIC FOR FLOOR 130 CM WIDTH (MIN)

APPENDIX "A, B & C" AND CLAUSE 6.1.1 OF SPECN CQAE/1940/1548/g

POLYCHLOROPRENE SYNTHETIC RUBBER (NEOPRENE) COATED 101 CMS (MIN) FOR BAFFLE WALL

Appendix " D" of Specn CQAE/1940/1548/g

LEAD SEAL SIZE 1/2" DIA TO DRG. NO. OFBA/NR/613 DTD.09.12.06

LEAD SEAL SIZE 1/2" DIA TO DRG. NO. OFBA/NR/613 DTD.09.12.06

LEAD OXIDE (LITHARGE) REQUIRED FOR MANUFACTURE OF ROCKET PROP.AND SINGLE BASE PROPELLANT AS PER SPECN. JSS 6810-111 2017 (3rd Rev)

LEAD OXIDE (LITHARGE) REQUIRED FOR MANUFACTURE OF ROCKET PROP.AND SINGLE BASE PROPELLANT AS PER SPECN. JSS 6810-111 2017 (3rd Rev)

• MSME

• LEAD OXIDE (LITHARGE) REQUIRED FOR MANUFACTURE OF ROCKET PROP.AND SINGLE BASE PROPELLANT AS PER SPECN. JSS 6810-111 2017 (3rd Rev)

ISOPHORONE DI-ISOCYNATE (IPDI), MERCK/FLUKA, SPECN :- I) PURITY (MINIMIM) -98%, II) DENSITY G/CM CUBE-1.06 PLUS MINUS 0.05 MAKE - MERCK/FLUKA.

ISOPHORONE DI-ISOCYNATE (IPDI), MERCK/FLUKA, SPECN :- I) PURITY (MINIMIM) -98%, II) DENSITY G/CM CUBE-1.06 PLUS MINUS 0.05 MAKE - MERCK/FLUKA.

IRON (III), ACETYLACETONATE, (FeAA) 97% NOF 300

IRON (III), ACETYLACETONATE, (FeAA) 97% NOF 300

INDUSTRIAL X-RAY FILMS CONFORMING TO IS:2595:2008 (Reaffirmed Year : 2020 )G-III CLASS OR MAKE: NDT-65 OR IRF-150 OR AGFA-D7 OR INDUSTREX AA-400 ARE ALSO ACCEPTABLE. SIZE:30 X 40 CM, AS PER SPECIFICATION ATTACHED.

INDUSTRIAL X-RAY FILMS CONFORMING TO IS:2595:2008 (Reaffirmed Year : 2020 )G-III CLASS OR MAKE: NDT-65 OR IRF-150 OR AGFA-D7 OR INDUSTREX AA-400 ARE ALSO ACCEPTABLE. SIZE:30 X 40 CM, AS PER SPECIFICATION ATTACHED.

• MSME

• INDUSTRIAL X-RAY FILMS CONFORMING TO IS:2595:2008 (Reaffirmed Year : 2020 )G-III CLASS OR MAKE: NDT-65 OR IRF-150 OR AGFA-D7 OR INDUSTREX AA-400 ARE ALSO ACCEPTABLE. SIZE:30 X 40 CM, AS PER SPECIFICATION ATTACHED.

B.F. Specification 1.20 Dtd 09.05.2022, confirm to specification JSS:6810-39:Latest Revision

B.F. Specification 1.20 Dtd 09.05.2022, confirm to specification JSS:6810-39:Latest Revision

• MSME

• B.F. Specification 1.20 Dtd 09.05.2022, confirm to specification JSS:6810-39:Latest Revision

HEXAMETHYLENE DIISOCYANATE, EX-MERCK/FLUKAASSAY:> 98% ( GC ), DENSITY : 1.05 G/CC (AT 20 C)IN 500 ML PACKING .

HEXAMETHYLENE DIISOCYANATE, EX-MERCK/FLUKAASSAY:> 98% ( GC ), DENSITY : 1.05 G/CC (AT 20 C)IN 500 ML PACKING .

CASE HEMK-1 (MODIFIED)L/A WOOD TO DRG.NO.IND/ME/29 DC NO 3604-ME DT.13.12.99.

CASE HEMK-1 (MODIFIED)L/A WOOD TO DRG.NO.IND/ME/29 DC NO 3604-ME DT.13.12.99.

DRG. NO. IND/ME/29, DC NO. 3604-ME DTD. 13.12.99

• MSME

• CASE HEMK-1 (MODIFIED)L/A WOOD TO DRG.NO.IND/ME/29 DC NO 3604-ME DT.13.12.99.

HARDENER EH 411/YUVA H-50/RC-206 HD HEMRL/TRIM/PROP/IM/15, DOC NO.-HEMRL/PIN/MQAP/6, REV NO.-6.

HARDENER EH 411/YUVA H-50/RC-206 HD HEMRL/TRIM/PROP/IM/15, DOC NO.-HEMRL/PIN/MQAP/6, REV NO.-6.

• MSME

• HARDENER EH 411/YUVA H-50/RC-206 HD HEMRL/TRIM/PROP/IM/15, DOC NO.-HEMRL/PIN/MQAP/6, REV NO.-6.

H.T.P.B. ( HYDROXY TERMINATED POLY BUTADIENE ) SPECIFICATION :-HEMRL/TRIM/PROP/RM/4.(REVISED).DT OF REVISION;09/01/2013.

H.T.P.B. ( HYDROXY TERMINATED POLY BUTADIENE ) SPECIFICATION :-HEMRL/TRIM/PROP/RM/4.(REVISED).DT OF REVISION;09/01/2013.

• MSME

• H.T.P.B. ( HYDROXY TERMINATED POLY BUTADIENE ) SPECIFICATION :-HEMRL/TRIM/PROP/RM/4.(REVISED).DT OF REVISION;09/01/2013.

GUN POWDER FOR 155MM AMMUNITION AS PER SPECN. IND/ME/974 (2016) DC NO 6010-ME, DT-03.02.2017

GUN POWDER FOR 155MM AMMUNITION AS PER SPECN. IND/ME/974 (2016) DC NO 6010-ME, DT-03.02.2017

• MSME

• GUN POWDER FOR 155MM AMMUNITION AS PER SPECN. IND/ME/974 (2016) DC NO 6010-ME, DT-03.02.2017

GRAPHITE DRY SULPHUR FREE TO SPECN. NO. JSS-9620-01-2021 (REV.NO.4), SIZE - 63 MICROMETER.

GRAPHITE DRY SULPHUR FREE TO SPECN. NO. JSS-9620-01-2021 (REV.NO.4), SIZE - 63 MICROMETER.

• MSME

• GRAPHITE DRY SULPHUR FREE TO SPECN. NO. JSS-9620-01-2021 (REV.NO.4), SIZE - 63 MICROMETER.

GLYCERINE FOR NITRATION TO SPECN.NO. JSS-6810-109:2013 REVISION NO 3, DC 5219-ME DTD.12.04.14. ALONGWITH SULPHURIC ACID COLOURATION TEST. THE GLYCERINE MUST PASS THROUGH THE SULPHURIC ACID COLOURATION TEST.

GLYCERINE FOR NITRATION TO SPECN.NO. JSS-6810-109:2013 REVISION NO 3, DC 5219-ME DTD.12.04.14. ALONGWITH SULPHURIC ACID COLOURATION TEST. THE GLYCERINE MUST PASS THROUGH THE SULPHURIC ACID COLOURATION TEST.

• MSME

• GLYCERINE FOR NITRATION TO SPECN.NO. JSS-6810-109:2013 REVISION NO 3, DC 5219-ME DTD.12.04.14. ALONGWITH SULPHURIC ACID COLOURATION TEST. THE GLYCERINE MUST PASS THROUGH THE SULPHURIC ACID COLOURATION TEST.

FORMALDEHYDE SOLUTION 37-41 % W/V, A.R.GRADE IN 2500 ML PACKING SPECIFICATION NO.- IS :3321-1973. REAFFIRMED 2015

FORMALDEHYDE SOLUTION 37-41 % W/V, A.R.GRADE IN 2500 ML PACKING SPECIFICATION NO.- IS :3321-1973. REAFFIRMED 2015

• MSME

• FORMALDEHYDE SOLUTION 37-41 % W/V, A.R.GRADE IN 2500 ML PACKING SPECIFICATION NO.- IS :3321-1973. REAFFIRMED 2015

DECOPPERING AGENT FOR CHARGE 8 & 9 DRG.NO. 6388122 155 MM FH 77 B- DC NO. 36819-A DT- 15.03.2002.

DECOPPERING AGENT FOR CHARGE 8 & 9 DRG.NO. 6388122 155 MM FH 77 B- DC NO. 36819-A DT- 15.03.2002.

• MSME

• DECOPPERING AGENT FOR CHARGE 8 & 9 DRG.NO. 6388122 155 MM FH 77 B- DC NO. 36819-A DT- 15.03.2002.

TYPE- ANTIMONY TRIOXIDE(SB203), COLOUR & APPEARANCE- WHITE, ODOURLESS,CRYSTALLINE POWDER, PURITY 99.5% SIEVE SIZE-ALL PASSING THROUGH -200BSS ,SPECFIC GRAVITY 5.67 g/cc HEMRL/TRIM/PROP/IM/17, DOC NO.-HEMRL/PIN/MQAP/6, REV NO.-6.

TYPE- ANTIMONY TRIOXIDE(SB203), COLOUR & APPEARANCE- WHITE, ODOURLESS,CRYSTALLINE POWDER, PURITY 99.5% SIEVE SIZE-ALL PASSING THROUGH -200BSS ,SPECFIC GRAVITY 5.67 g/cc HEMRL/TRIM/PROP/IM/17, DOC NO.-HEMRL/PIN/MQAP/6, REV NO.-6.

• MSME

• TYPE- ANTIMONY TRIOXIDE(SB203), COLOUR & APPEARANCE- WHITE, ODOURLESS,CRYSTALLINE POWDER, PURITY 99.5% SIEVE SIZE-ALL PASSING THROUGH -200BSS ,SPECFIC GRAVITY 5.67 g/cc HEMRL/TRIM/PROP/IM/17, DOC NO.-HEMRL/PIN/MQAP/6, REV NO.-6.

EXPANDED POLYSTYRENE SELF EXTINGUISHING TYPE(TYPE 2) DENSITY 30 KG/CU.M.CONFORMING TO CLAUSE 4.5.1 OF SPECIFICATION IS: 4671-1984 ( FIRST REV.) REAFFIRMED 2017 TO CQA(A) DRAWING NO 13981-1.0 DC 35707-A DTD 5-5-94 SIZE 108MM PLUS MINUS 2MM X 108MM PLUS MINUS 2MM X 64MM PLUS MINUS 2MM.

EXPANDED POLYSTYRENE SELF EXTINGUISHING TYPE(TYPE 2) DENSITY 30 KG/CU.M.CONFORMING TO CLAUSE 4.5.1 OF SPECIFICATION IS: 4671-1984 ( FIRST REV.) REAFFIRMED 2017 TO CQA(A) DRAWING NO 13981-1.0 DC 35707-A DTD 5-5-94 SIZE 108MM PLUS MINUS 2MM X 108MM PLUS MINUS 2MM X 64MM PLUS MINUS 2MM.

• MSME

• EXPANDED POLYSTYRENE SELF EXTINGUISHING TYPE(TYPE 2) DENSITY 30 KG/CU.M.CONFORMING TO CLAUSE 4.5.1 OF SPECIFICATION IS: 4671-1984 ( FIRST REV.) REAFFIRMED 2017 TO CQA(A) DRAWING NO 13981-1.0 DC 35707-A DTD 5-5-94 SIZE 108MM PLUS MINUS 2MM X 108MM PLUS MINUS 2MM X 64MM PLUS MINUS 2MM.

ETHYLENE GLYCOL MONOETHYLETHER (CELLOSOLVE SOLVENT) SPECN. NO. IND/ME/422 (a) 3754-ME-DT.12.12.2002.

ETHYLENE GLYCOL MONOETHYLETHER (CELLOSOLVE SOLVENT) SPECN. NO. IND/ME/422 (a) 3754-ME-DT.12.12.2002.

• MSME

• ETHYLENE GLYCOL MONOETHYLETHER (CELLOSOLVE SOLVENT) SPECN. NO. IND/ME/422 (a) 1976 DC NO 3754-ME DT.12.12.2002.

ETHYL CELLULOSE HIGH VISCOSITY TYPE N-200 CONFORMING TO SPCN CS-2724.THE MATERIAL WILL BE ACCEPTED AFTER TRIAL EXTRUSION OF SMOOTH AND TRANSPARENT E.C.SLEEVES WITHOUT ANY WRINKLES AND UNMOLTEN PARTICLES AND FREE FROM FOREIGN MATTER AND MEETING MECHANICAL PROPERTIES.

ETHYL CELLULOSE HIGH VISCOSITY TYPE N-200 CONFORMING TO SPCN CS-2724.THE MATERIAL WILL BE ACCEPTED AFTER TRIAL EXTRUSION OF SMOOTH AND TRANSPARENT E.C.SLEEVES WITHOUT ANY WRINKLES AND UNMOLTEN PARTICLES AND FREE FROM FOREIGN MATTER AND MEETING MECHANICAL PROPERTIES.

• MSME

• MSME

ETHER SOLVENT GRADE(STABILISER FREE)TO SPECIFICATION NO. IS-336-1973(SECOND REVISION) REAFFIRMED -2018

ETHER SOLVENT GRADE(STABILISER FREE)TO SPECIFICATION NO. IS-336-1973(SECOND REVISION) REAFFIRMED -2018

• MSME

• ETHER SOLVENT GRADE(STABILISER FREE)TO SPECIFICATION NO. IS-336-1973(SECOND REVISION) REAFFIRMED -2018

WASHER END WHITE NORMAL ARROW CHARGES TO DRG NO. OFBA/RK/221 DT.02.07.83

WASHER END WHITE NORMAL ARROW CHARGES TO DRG NO. OFBA/RK/221 DT.02.07.83

• MSME

• WASHER END WHITE NORMAL ARROW CHARGES TO DRG NO. OFBA/RK/221 DT.02.07.83

DI PHENYL METHANE DI-ISOCYNATE. TO HEMRL Spcn. No. HEMRL/ED/ PS/318 Origional Sealed bottle of "Merck" made

DI PHENYL METHANE DI-ISOCYNATE. TO HEMRL Spcn. No. HEMRL/ED/ PS/318 Origional Sealed bottle of "Merck" made

• MSME

• DI PHENYL METHANE DI-ISOCYNATE. TO HEMRL Spcn. No. HEMRL/ED/ PS/318 Origional Sealed bottle of "Merck" made

DIPHENYLAMINE CONFORMING TO SPECIFICATION GOST 194-80

DIPHENYLAMINE CONFORMING TO SPECIFICATION GOST 194-80

• MSME

• DIPHENYLAMINE CONFORMING TO SPECIFICATION GOST 194-80

DIOCTYLE PHTHALATE AS PER SPECN.NO. IS 14421:1997 REAFFIRMED -2018. TEST TO BE CARRIED OUT FOR CHARACTERISTICS,1)RELATIVE DENSITY 2)REFRACTIVE INDEX 3)WATER CONTENT 4)ACID VALUE 5) ESTER (SAPHONIFICATION) VALUE

DIOCTYLE PHTHALATE AS PER SPECN.NO. IS 14421:1997 REAFFIRMED -2018. TEST TO BE CARRIED OUT FOR CHARACTERISTICS,1)RELATIVE DENSITY 2)REFRACTIVE INDEX 3)WATER CONTENT 4)ACID VALUE 5) ESTER (SAPHONIFICATION) VALUE

• MSME

• DIOCTYLE PHTHALATE AS PER SPECN.NO. IS 14421:1997 REAFFIRMED -2018. TEST TO BE CARRIED OUT FOR CHARACTERISTICS,1)RELATIVE DENSITY 2)REFRACTIVE INDEX 3)WATER CONTENT 4)ACID VALUE 5) ESTER (SAPHONIFICATION) VALUE

TAPE NYLON 2.54 CM U/D BS 227 KG

DRG. NO. IS 6349-1981

RUBBER WEDGE

SPECIFICATION NO.:ADRDE/1106-A-1/SA-5(a)

SPECIFICATION: ADRDE/1394(a)

SPECIFICATION: ADRDE/1394(a)

A4/5340-006721 BUCKLE WAIST ADJUSTABLE ADOPTER (SLIDING BAR TYPE) PTRM SPECN.NO.IND/GS/1802

SPECN.NO.IND/GS/1802

IND/GS/1802

Needle Valve Carburator MCT 3215

Needle Valve Carburator MCT 3215

MCT 3215

FABRIC NYLON LT. WT. 37 GM RIPSTOP WEAVE OLIVE DRAB SHADE NO 298 ASPER IS:SPECN NO.IS:5-1994 122 CM WIDTH

SPECN. NO. IS:4726-1984 Except that :-(i) Page 4, Clause 2.2.1, third line has been deleted from IS. (ii) Page 7, Table 1, Note 2 has been amended as given For - 210 g/cm2 Read-200 g/cm2

• As Per Specification/Drawing

• As Per Specification/Drawing

HARLEY BUCKLE

ADRDE/1308(c)

• As per Specification/Drawing

• As per Specification/Drawing

FEMALE COUPLING FOR CWL

DRG. NO. ADRDE/1344(b)

DRG. NO. ADRDE/1344(b)

• As per Specification

• As per Specification

SUPPLY OF PACKING BOX FOR 10 NOS AS PER DRG NO K 9024STR WITH FIRMS MATERIAL

SUPPLY OF PACKING BOX FOR 10 NOS AS PER DRG NO K 9024STR WITH FIRMS MATERIAL

K 9024STR

Button Polyester 19 mm OG (OCFAV/Button/002)

IS:1461-1984 Second Revision (Reaffirmed-2003) and Supplementary Scheduled no. CQA (GS)/SS/346(b) Except that: (i) Material shall be polyester. (ii) Design & Dimensions: As per Drawing Enclosed (Drg. No. OCFAV/Button/002). (iii) In app. Feel, Finish and all other resp. not defi. in this spec. Button shall confirm to the corres. sealed sample held in the cust. of the contro. customer service centre, OCF Avadi.

• as per attached manufacturing technology files

• as per attached testing/inspection facility files

Assy Parasal to drg no 6795 208 SB 6850

Assy Parasal to drg no 6795 208 SB 6850

DINITROTOLUENE GRADE 1 CONFORMING TO SPECIFICATION NUMBER JSS-1376-04 : 2019(REVISION NO. 4).

DINITROTOLUENE GRADE 1 CONFORMING TO SPECIFICATION NUMBER JSS-1376-04 : 2019(REVISION NO. 4).

• MSME

• DINITROTOLUENE GRADE 1 CONFORMING TO SPECIFICATION NUMBER JSS-1376-04 : 2019(REVISION NO. 4)

TYPE- MONOEPOXY, COLOUR & APPEARANCE -BROWN CLEAR LIQUID, DENSITY AT 25 DEG. CEL. 0.985 g/ml, VISCOSITY AT 25 DEG. CEL. 100 cps. EPOSIDE EQUIVALENT 550+ 50

TYPE- MONOEPOXY, COLOUR & APPEARANCE -BROWN CLEAR LIQUID, DENSITY AT 25 DEG. CEL. 0.985 g/ml, VISCOSITY AT 25 DEG. CEL. 100 cps. EPOSIDE EQUIVALENT 550+ 50

DICHLOROMETHANE. AR GRADE, EX-S.D. FINE/GLAXO PURITY : MIN. 99.5 %, WATER : MAX. 0.02 % IN 2.5 LITRE PACKINGS.

DICHLOROMETHANE. AR GRADE, EX-S.D. FINE/GLAXO PURITY : MIN. 99.5 %, WATER : MAX. 0.02 % IN 2.5 LITRE PACKINGS.

DIAMYL PHTHALATE CONFORMING TO SPECN NO.IND/ME/872 : 2015 DC - 5383-ME, DT. 21.12.2015.

DIAMYL PHTHALATE CONFORMING TO SPECN NO.IND/ME/872 : 2015 DC - 5383-ME, DT. 21.12.2015.

• MSME

• DIAMYL PHTHALATE CONFORMING TO SPECN NO.IND/ME/872 : 2015 DC - 5383-ME, DT. 21.12.2015.

IND/ME/873(A)Prov.DC No.3754-ME,dated 12.12.2002

IND/ME/873(A)Prov.DC No.3754-ME,dated 12.12.2002

SPECN: IS 9591: 1996 (REAFFIRMED-2018) 1)RELATIVE DENSITY AT 20DEG C 0.913 TO 0.919G/CC2)REFRACTIVEINDEXAT 20 DEGC 1.450-1.454.3)WATER CONTENT:0.1%(MAX)4)ASH%:0.01(MAX) 5)ACIDITY(AS SEBACIC ACID):0.02%(MAX)6)ESTER CONTENT:99.5% (MIN) 7)MATTER OXIDIZABLE BY POTASSIUM DICHROMATE :0.3 % MAX

SPECN: IS 9591: 1996 (REAFFIRMED-2018) 1)RELATIVE DENSITY AT 20DEG C 0.913 TO 0.919G/CC2)REFRACTIVEINDEXAT 20 DEGC 1.450-1.454.3)WATER CONTENT:0.1%(MAX)4)ASH%:0.01(MAX) 5)ACIDITY(AS SEBACIC ACID):0.02%(MAX)6)ESTER CONTENT:99.5% (MIN) 7)MATTER OXIDIZABLE BY POTASSIUM DICHROMATE :0.3 % MAX

• MSME

• SPECN: IS 9591: 1996 (REAFFIRMED-2018) 1)RELATIVE DENSITY AT 20DEG C 0.913 TO 0.919G/CC2)REFRACTIVEINDEXAT 20 DEGC 1.450-1.454.3)WATER CONTENT:0.1%(MAX)4)ASH%:0.01(MAX) 5)ACIDITY(AS SEBACIC ACID):0.02%(MAX)6)ESTER CONTENT:99.5% (MIN) 7)MATTER OXIDIZABLE BY POTASSIUM DICHROMATE :0.3 % MAX

HULL ELECTRICAL EQUIPMENT 6795 82 CB6000 KIT B

HULL ELECTRICAL EQUIPMENT 6795 82 CB6000 KIT B

Specn-ERDL/TRIM/Prov/RM/5

Specn-ERDL/TRIM/Prov/RM/5

.(CATALYST)MERCK/ALDRICH. PURITY (TIN CONTENT)- >97%Molecular weight (MW)- 631.55 g/molDENSITY: 1 Ltr=1.05 KGMinimum assay (Sn)>97% - ONLY MERCK/ALDRICH MAKE ACCEPTABLE

.(CATALYST)MERCK/ALDRICH. PURITY (TIN CONTENT)- >97%Molecular weight (MW)- 631.55 g/molDENSITY: 1 Ltr=1.05 KGMinimum assay (Sn)>97% - ONLY MERCK/ALDRICH MAKE ACCEPTABLE

GALVANIZED STEEL SHEET TYPE DEEP DRAWING DESIGNATION B GPO TO SPECN. IS:277-2003. AS PER DRG. NO. OFBA/CX/51 DT.24.02.1989 & 05.01.2007 (FOR ITEM NO. 5 & 6) AMENDED ON DT.10.10.2008. TRACED FROM DRG.NO. DD (L) 16472 B AMENDED VIDE DC. NO. 37189-A DT. 22.09.2008. INCLUDING FELT DISC.

GALVANIZED STEEL SHEET TYPE DEEP DRAWING DESIGNATION B GPO TO SPECN. IS:277-2003. AS PER DRG. NO. OFBA/CX/51 DT.24.02.1989 & 05.01.2007 (FOR ITEM NO. 5 & 6) AMENDED ON DT.10.10.2008. TRACED FROM DRG.NO. DD (L) 16472 B AMENDED VIDE DC. NO. 37189-A DT. 22.09.2008. INCLUDING FELT DISC.

DRG. NO. OFBA/CX/51 DT.24.02.1989 & 05.01.2007 (FOR ITEM NO. 5 & 6) AMENDED ON DT.10.10.2008. TRACED FROM DRG.NO. DD (L) 16472 B AMENDED VIDE DC. NO. 37189-A DT. 22.09.2008. INCLUDING FELT DISC.

• MSME

• CYLINDER 443 MK1/L"GALVANIZED STEEL SHEET TYPE"DEEP DRAWING" DESIGNATION 'GPD' TO SPECN.IS:277-2003"AS PER DRG.NO OFBA/CX /51 DT 24/2/89 & 5/1/07 (FOR ITEM NO. 5 & 6) AMENDED ON DTD. 10.10.08 TRACED FROMDRG.NO DD(L) 16472 B AMENDED VIDE DC-37 189-A DT.22/09/08.INCLUDING FELT DISC.

CYLINDER 12A STEEL FOR AMMUNITION, CONTAINER ASSEMBLY 117A. AS PER DRG.NO CIA/AMN/1833, PART NO ISV 453A.(SERVICEABLE)/ DRG.NO.OFBA/NR/423 TO 428.

CYLINDER 12A STEEL FOR AMMUNITION, CONTAINER ASSEMBLY 117A. AS PER DRG.NO CIA/AMN/1833, PART NO ISV 453A.(SERVICEABLE)/ DRG.NO.OFBA/NR/423 TO 428.

DRG.NO CIA/AMN/1833, PART NO ISV 453A.(SERVICEABLE)/ DRG.NO.OFBA/NR/423 TO 428.

• MSME

• DRG.NO CIA/AMN/1833, PART NO ISV 453A.(SERVICEABLE)/ DRG.NO.OFBA/NR/423 TO 428.

CUTTING AND STITCHING OF CHARGE BAGS FOR CHARGE 9 OF 155MM AMMN.AS PER DRG.NO-6388103,6388104,6388106,6388115,6388116, 6355588,5191810,5173926,4090246,4090247,4079932. MATERIAL WILL BE SUPPLIED BY OFBA.

CUTTING AND STITCHING OF CHARGE BAGS FOR CHARGE 9 OF 155MM AMMN.AS PER DRG.NO-6388103,6388104,6388106,6388115,6388116, 6355588,5191810,5173926,4090246,4090247,4079932. MATERIAL WILL BE SUPPLIED BY OFBA.

CUTTING AND STITCHING OF CHARGE BAGS FOR CHARGE 9 OF 155MM AMMN.AS PER DRG.NO-6388103,6388104,6388106,6388115,6388116, 6355588,5191810,5173926,4090246,4090247,4079932. MATERIAL WILL BE SUPPLIED BY OFBA.

CUTTING & STITCHING OF CHARGE BAGS FOR M4A2 AS PER DRG.NO- 12882-2-0 TO 12884-2-0,12885-1-0,12886-0-0,12887-0-0,12888-1 -0,12890-2-0,NO 12909-0-0 , 12910-0-0,14776-0-0 TO 14778-0- 0,13976-0-0,12891-0-0,12899-0-0,12905-0-0. MATERIAL WILL BE SUPPLIED BY OFBA.

CUTTING & STITCHING OF CHARGE BAGS FOR M4A2 AS PER DRG.NO- 12882-2-0 TO 12884-2-0,12885-1-0,12886-0-0,12887-0-0,12888-1 -0,12890-2-0,NO 12909-0-0 , 12910-0-0,14776-0-0 TO 14778-0- 0,13976-0-0,12891-0-0,12899-0-0,12905-0-0. MATERIAL WILL BE SUPPLIED BY OFBA.

CUTTING & STITCHING OF CHARGE BAGS FOR M4A2 AS PER DRG.NO- 12882-2-0 TO 12884-2-0,12885-1-0,12886-0-0,12887-0-0,12888-1 -0,12890-2-0,NO 12909-0-0 , 12910-0-0,14776-0-0 TO 14778-0- 0,13976-0-0,12891-0-0,12899-0-0,12905-0-0. MATERIAL WILL BE SUPPLIED

• MSME

• CUTTING & STITCHING OF CHARGE BAGS FOR M4A2 AS PER DRG.NO- 12882-2-0 TO 12884-2-0,12885-1-0,12886-0-0,12887-0-0,12888-1 -0,12890-2-0,NO 12909-0-0 , 12910-0-0,14776-0-0 TO 14778-0- 0,13976-0-0,12891-0-0,12899-0-0,12905-0-0. MATERIAL WILL BE SUPPLIED BY OFBA.

CRUDE BEES WAX AS PER SPECIFICATION NO. IS-1504-1996 REAFFIRMED 2014.

CRUDE BEES WAX AS PER SPECIFICATION NO. IS-1504-1996 REAFFIRMED 2014.

• MSME

• CRUDE BEES WAX AS PER SPECIFICATION NO. IS-1504-1996 REAFFIRMED 2014.

CRATE 5 A/L WIRE BOUND FOR PACKAGE AMMUNITION 79A TO DRG.NO OFBA/CX/55 DTS-16.08.94 AMMENDED ON 15.02.02. TRACED FROM CI(A)/AMN/754 PART NO ISV 326A DC (I) 30562-A SPECN. IA 948 (a.f ) DC 36081A.

CRATE 5 A/L WIRE BOUND FOR PACKAGE AMMUNITION 79A TO DRG.NO OFBA/CX/55 DTS-16.08.94 AMMENDED ON 15.02.02. TRACED FROM CI(A)/AMN/754 PART NO ISV 326A DC (I) 30562-A SPECN. IA 948 (a.f ) DC 36081A.

DRG.NO OFBA/CX/55 DTS-16.08.94 AMMENDED ON 15.02.02

• MSME

• CRATE 5 A/L WIRE BOUND FOR PACKAGE AMMUNITION 79A TO DRG.NO OFBA/CX/55 DTS-16.08.94 AMMENDED ON 15.02.02. TRACED FROM CI(A)/AMN/754 PART NO ISV 326A DC (I) 30562-A SPECN. IA 948 (a.f ) DC 36081A.

Crepe/Natural Rubber Grade PLC-I or PLC-I -X to Defense Specification No. IND/ME/748(b), DC- 3754-ME, Dt:12/12/2002.

Crepe/Natural Rubber Grade PLC-I or PLC-I -X to Defense Specification No. IND/ME/748(b), DC- 3754-ME, Dt:12/12/2002.

• MSME

• Crepe/Natural Rubber Grade PLC-I or PLC-I -X to Defense Specification No. IND/ME/748(b), DC- 3754-ME, Dt:12/12/2002.

COTTON YARN NE 2/2 CONFORMING TO SPECIFICATION NO.IND/ME/800 DC3754-ME DTD. 12.12.2002 "MATERIAL TO BE SUPPLIED AS PER OFBaDrg.No.OFBA/CX/85 dt.22.03.2006 for Cotton Yarn NE 2/2 Bundle.

COTTON YARN NE 2/2 CONFORMING TO SPECIFICATION NO.IND/ME/800 DC3754-ME DTD. 12.12.2002 "MATERIAL TO BE SUPPLIED AS PER OFBaDrg.No.OFBA/CX/85 dt.22.03.2006 for Cotton Yarn NE 2/2 Bundle.

OFBaDrg.No.OFBA/CX/85 dt.22.03.2006 for Cotton Yarn NE 2/2 Bundle.

SPECN. NO. IND/ME/800-DC-3754-ME DATED 12.12.2000 & DRG NO. OFBA/CX/86 DT 23/03/2006 AMENDED ON DTD. 29/09/2008

SPECN. NO. IND/ME/800-DC-3754-ME DATED 12.12.2000 & DRG NO. OFBA/CX/86 DT 23/03/2006 AMENDED ON DTD. 29/09/2008

WHITE COLOURED CLOTH COTTON DOWN TIGHT TO SPECN. IND/ME/1005 (OCT.2012), DC 5105-ME DT.27-04-2013, WIDTH:1400 MM.

WHITE COLOURED CLOTH COTTON DOWN TIGHT TO SPECN. IND/ME/1005 (OCT.2012), DC 5105-ME DT.27-04-2013, WIDTH:1400 MM.

• MSME

• WHITE COLOURED CLOTH COTTON DOWN TIGHT TO SPECN. IND/ME/1005 (OCT.2012), DC 5105-ME DT.27-04-2013, WIDTH:1400 MM.

CORUGATED CARD BOARD SHEET EACH ST CONSIST OF A) PKG. SHEET IV HEMRL/ED/DRG NO. 002 DET NO.1 SIZE 470X180X10MM THK, 4 NOS/SET B)PKG. SHEET V DET NO.2 SIZE 170X160X20MM THK, 2 NOS/SET C)PKG. SHEETVI DET NO.3 SIZE 135X160X40MM THK, 1 NOS/SET D)PKG. SHEET VII DET NO.4 SIZE 410X160X25MM THK, 1 NOS/SET

CORUGATED CARD BOARD SHEET EACH ST CONSIST OF A) PKG. SHEET IV HEMRL/ED/DRG NO. 002 DET NO.1 SIZE 470X180X10MM THK, 4 NOS/SET B)PKG. SHEET V DET NO.2 SIZE 170X160X20MM THK, 2 NOS/SET C)PKG. SHEETVI DET NO.3 SIZE 135X160X40MM THK, 1 NOS/SET D)PKG. SHEET VII DET NO.4 SIZE 410X160X25MM THK, 1 NOS/SET

CORRUGATED SHEET ABC SIZE

CORRUGATED CARD BOARD SHEET EACH SET CONSIST OF A) PACKING SHEET I HEMRL/ED/DRG NO.. 001 DETL NO 1 SIZE 600X225X32.5MM THICK, 18 NOS ./SET B)PACKING SHEET II DETL NO.2 SIZE 590X 235X42.5MM THICK, 18 NOS. /SET C) PKG. SHEET III DETL NO. 3 SIZE 235X140X12 MM THICK 27 NOS. /SET

CORRUGATED CARD BOARD SHEET EACH SET CONSIST OF A) PACKING SHEET I HEMRL/ED/DRG NO.. 001 DETL NO 1 SIZE 600X225X32.5MM THICK, 18 NOS ./SET B)PACKING SHEET II DETL NO.2 SIZE 590X 235X42.5MM THICK, 18 NOS. /SET C) PKG. SHEET III DETL NO. 3 SIZE 235X140

COMPRESSION CANISTER LOAD CELL RANGE 1 TON (10 KN) AS PER ATTACHED SPECIFICATION.

COMPRESSION CANISTER LOAD CELL RANGE 1 TON (10 KN) AS PER ATTACHED SPECIFICATION.

CLOTH COTTON DOSUTI BL 36 INCHES WIDE AS PER SPECN.NO. IS:179-2009 (Reaffirmed 2018)

CLOTH COTTON DOSUTI BL 36 INCHES WIDE AS PER SPECN.NO. IS:179-2009 (Reaffirmed 2018)

• MSME

• CLOTH COTTON DOSUTI BL 36 INCHES WIDE AS PER SPECN.NO. IS:179-2009 (Reaffirmed 2018)

SCLOTH CHINA SHEETING NO.1 GREY 36 INCHES WIDE (91.5 CMS) AS PER B.F. SPECN. NO. 1.10 DTD. 28.08.82,AMENDED ONDTD. 11.11. 2013.(EXTRACT ATTACHED).

CLOTH CHINA SHEETING NO.1 GREY 36 INCHES WIDE (91.5 CMS) AS PER B.F. SPECN. NO. 1.10 DTD. 28.08.82,AMENDED ONDTD. 11.11. 2013.(EXTRACT ATTACHED).

• MSME

• CLOTH CHINA SHEETING NO.1 GREY 36 INCHES WIDE (91.5 CMS) AS PER B.F. SPECN. NO. 1.10 DTD. 28.08.82,AMENDED ONDTD. 11.11. 2013.(EXTRACT ATTACHED).

DRG.NO.-OFBA/BT/52 G/1, OFBA/BT/52 G/1/1, OFBA/BT/53G/1, OFBA/BT/53G/1/1 INNER BOX TO BE WAX COATED INSIDE AND OUTSIDE SURFACE. OUTER BOX TO BE WAX COATED INSIDE SURFACE ONLY.

DRG.NO.-OFBA/BT/52 G/1, OFBA/BT/52 G/1/1, OFBA/BT/53G/1, OFBA/BT/53G/1/1 INNER BOX TO BE WAX COATED INSIDE AND OUTSIDE SURFACE. OUTER BOX TO BE WAX COATED INSIDE SURFACE ONLY.

• MSME

• DRG.NO.-OFBA/BT/52 G/1, OFBA/BT/52 G/1/1, OFBA/BT/53G/1, OFBA/BT/53G/1/1 INNER BOX TO BE WAX COATED INSIDE AND OUTSIDE SURFACE. OUTER BOX TO BE WAX COATED INSIDE SURFACE ONLY.

CLOTH ACRYLIC RAYON GRADE "B" TO SPECN IND/ME/973(A)2016 DC 6009-ME DT.03.02.2017. WIDTH NOT LESS THAN 1 MTR.

CLOTH ACRYLIC RAYON GRADE "B" TO SPECN IND/ME/973(A)2016 DC 6009-ME DT.03.02.2017. WIDTH NOT LESS THAN 1 MTR.

• MSME

• CLOTH ACRYLIC RAYON GRADE "B" TO SPECN IND/ME/973(A)2016 DC 6009-ME DT.03.02.2017. WIDTH NOT LESS THAN 1 MTR.

CLOTH ACRYLIC RAYON WHITE TO SPECIFICATION IND/ME/973(A) 2016 GRADE A DC NO. 6009 ME DATED 03.02.2017. WIDTH NOT LESS THAN 1.22 METRE.

CLOTH ACRYLIC RAYON WHITE TO SPECIFICATION IND/ME/973(A) 2016 GRADE A DC NO. 6009 ME DATED 03.02.2017. WIDTH NOT LESS THAN 1.22 METRE.

• MSME

• CLOTH ACRYLIC RAYON WHITE TO SPECIFICATION IND/ME/973(A) 2016 GRADE A DC NO. 6009 ME DATED 03.02.2017. WIDTH NOT LESS THAN 1.22 METRE.

AS PER DRG NO. CI(A)635595 & CQA(A) 6391044

AS PER DRG NO. CI(A)635595 & CQA(A) 6391044

• MSME

• AS PER DRG NO. CI(A)635595 & CQA(A) 6391044

CASE C-128MK-13/L TO DRG.NO.IA-1031/OFBA/RK/514 DTD.31.12.07 DC NO.36234-A.DT-4.2.97 & SPECN- NO.IA-948 (A.F) DC NO.36081 -A (WITHOUT GROOVES AND PARTITIONS).

CASE C-128MK-13/L TO DRG.NO.IA-1031/OFBA/RK/514 DTD.31.12.07 DC NO.36234-A.DT-4.2.97 & SPECN- NO.IA-948 (A.F) DC NO.36081 -A (WITHOUT GROOVES AND PARTITIONS).

• MSME

• CASE C-128MK-13/L TO DRG.NO.IA-1031/OFBA/RK/514 DTD.31.12.07 DC NO.36234-A.DT-4.2.97 & SPECN- NO.IA-948 (A.F) DC NO.36081 -A (WITHOUT GROOVES AND PARTITIONS).

CARTRIDGING PAPER GR-2 MACHINE GLASED(ONE SIDE ONLY) IN ROLL,BOBBIN DIA OF 800 MM, BOBBIN CENTER SLEEVE DIA OF 70 MM AND ROLL WIDTH OF 170 MM AS PER SPECN IS:1397 : 1990,Second Revision (Amendment NO 1)REAFFIRMED 2002.

CARTRIDGING PAPER GR-2 MACHINE GLASED(ONE SIDE ONLY) IN ROLL,BOBBIN DIA OF 800 MM, BOBBIN CENTER SLEEVE DIA OF 70 MM AND ROLL WIDTH OF 170 MM AS PER SPECN IS:1397 : 1990,Second Revision (Amendment NO 1)REAFFIRMED 2002.

CARTON BOX FOR LTPE CARTRIDGE TO HOLD 25 CARTRIGES 100 G EACH,EMPTY LONG FLAPS AS PER DRG.NO. OFBA/PE/11,THICKNESS OF CARTON BOARD 0.889 MM PLUS/MINUS 0.089 MM.

CARTON BOX FOR LTPE CARTRIDGE TO HOLD 25 CARTRIGES 100 G EACH,EMPTY LONG FLAPS AS PER DRG.NO. OFBA/PE/11,THICKNESS OF CARTON BOARD 0.889 MM PLUS/MINUS 0.089 MM.

DRG.NO. OFBA/PE/11,THICKNESS OF CARTON BOARD 0.889 MM PLUS/MINUS 0.089 MM.

• MSME

• CARTON BOX FOR LTPE CARTRIDGE TO HOLD 25 CARTRIGES 100 G EACH,EMPTY LONG FLAPS AS PER DRG.NO. OFBA/PE/11,THICKNESS OF CARTON BOARD 0.889 MM PLUS/MINUS 0.089 MM.

CARTG SA 5 POINT 56 MM BALL

CARTG. SA 5.56 MM BALL MK-I TO CQA (A) DRG NO. IQV 45 GF

CARTG. SA 5.56 MM BALL MK-I TO CQA (A) DRG NO. IQV 45 GF