PLUNGER REAR SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-315

BS: 970 PT.1 GR. 070 M55 OR EN 9

DRG. NO. TSP-315

BLADE FORE SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-316

BS: 970 EN 9 OR (IS:5517-93.55 C 8)

DRG. NO. TSP-316

LEAF REAR SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-310

BS: 970 PT.1 GR.070 M55 OR EN 9

DRG. NO. TSP-310

BAND FORE SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-303

STEEL BS 970 EN 8

DRG. NO. TSP-303

BRACKET REAR SIGHT FOR 30-06 SPORTING RIFLE DRG.TSP-302

B.S. 970 PT.I GR, 070 M55

DRG.TSP-302

CATCH SAFETY FOR 0.315" SPORTING RIFLE DRG. NO. SP-46

STEEL B.S. 970 PT.1:1983 GR. 070 M-55

DRG. NO. SP-46

SEAR FOR 0.315" SPORTING RIFLE DRG. NO. SP-60

STEEL B.S.970 PT-I/1983 GR. 080-M40

DRG. NO. SP-60

SPRING BOLT LOCKING FOR 0.315" SPORTING RIFLE DRG. NO. SP-62

B.S.970 PT.5:1972 GR.250 A-58 HRD. & TEMP. (480-52 VPN REF.)

DRG. NO. SP-62

RETICLE BTS7210037

RETICLE BTS7210037 OF K-10T

BTS7210037

WOODEN PACKING BOX TO DRG NO. 998-PB-3396 REQUIRED FOR HATCH TRAV.MECH-62 AS PER SCOPE OF WORK

WOODEN PACKING BOX TO DRG NO. 998-PB-3396

DRG NO. 998-PB-3396

Spring 0.8mm for RGB60 as per Drawing

As per drawing

NASK 1068/3

AS PER DRAWING.

AS PER DRAWING.

AS DRAWING

AS DRAWING

AS PER DRAWING.

AS PER DRAWING.

AS PER DRAWING.

AS PER DRAWING.

AS PER DRAWING.

AS PER DRAWING.

AS PER HAPP DRG. NO. C ROC 060 1 002

AS PER HAPP DRG. NO. C ROC 060 1 002

AS PER DRAWINGS

AS PER DRAWINGS

Spring 1.2mm for RGB60

As per Drawing

NASK1068/4

AS DRAWING

AS DRAWING

AS PER HAPP DRG. NO. C ROC 060 1 131

AS PER HAPP DRG. NO. C ROC 060 1 131

AS PER HAPP DRG. NO. C ROC 060 1 128

AS PER HAPP DRG. NO. C ROC 060 1 128

GUN POSITION SENDING UNIT TO DRAWING NO. BL5.132.045

GUN POSITION SENDING UNIT TO DRAWING NO. BL5.132.045

BL5.132.045

AS PER DRAWINGS

AS PER DRAWINGS

AS PER HAPP DRG. NO. C ROC 060 1 134

AS PER HAPP DRG. NO. C ROC 060 1 134

AS PER DRAWINGS

AS PER DRAWINGS

AS PER DRAWINGS

AS PER DRAWINGS

AS PER DRAWINGS

AS PER DRAWINGS

AS PER DRAWING.

AS PER DRAWING.

AS PER HAPP DRAWING

AS PER HAPP DRAWING

AS PER HAPP DRG. NO. C PLG 081 1 030

AS PER HAPP DRG. NO. C PLG 081 1 030

LINK CARTG. METALLIC BELT 7.62MM M13

TO DRG. NO. F-7268389, DC NO. 36977-A DTD. 24-08-2004 & TO SPECN. :- (I) CIA 4204(b) DC NO. 36977-A DTD. 24-08-2004 (II) JSS : 0465-01-1994 (REVISION NO. 1) NOTE :- MATERIAL TO BE PACKED AS PER 85 A/L TO DRG. NO. ISV 266 GA WHICH CONSIST OF CWP 14A, CARTON 11 A/L AND CARTON 12A

F-7268389, DC NO. 36977-A DTD. 24-08-2004

• Press Work

• As per QMI document

CARTON BOARD AMMN (787.4 x 558.8 x 0.508) TO SIZE :- 787.4MM x 558.8MM x 0.508MM (+/-) 0.051MM

JSS : 8135-15-2010 (REVISIONN NO. 2)

SODA ASH TATA MAKE OR EQUIVALENT INDIAN MAKE

IS : 251-1998 (FOURTH REVISION) REAFFIRMED 2010.

Sewing cotton 100 D Tex/6 Khaki in Tube of 1000 mtrs. Specification : IS:1720-1978 (VR. NO. 31) Second Revision (Reaffirmed 2012)

Sewing cotton 100 D Tex/6 Khaki in Tube of 1000 mtrs. Specification : IS:1720-1978 (VR. NO. 31) Second Revision (Reaffirmed 2012)

• as per attached list (Manufacturing Technology Files )

• as per attached list (Testing / Inspection Facility Files )

BLEACHED COTTON LINTERS SHALL CONFORM TO SPECIFICATION JSS: 8305-14 : 2020 (REVISION NO.5) INCLUDING CLAUSE 7.4.2. THE DYNAMIC VISCOSITY OF THE STORE SHOULD BE BETWEEN 10 TO 30 POISE FOR O.F.BHANDARA AGAINST THE DYNAMIC VISCOSITY RANGE 5 TO 50 POISE.

BLEACHED COTTON LINTERS SHALL CONFORM TO SPECIFICATION JSS: 8305-14 : 2020 (REVISION NO.5) INCLUDING CLAUSE 7.4.2. THE DYNAMIC VISCOSITY OF THE STORE SHOULD BE BETWEEN 10 TO 30 POISE FOR O.F.BHANDARA AGAINST THE DYNAMIC VISCOSITY RANGE 5 TO 50 POISE.

• MSME

• BLEACHED COTTON LINTERS SHALL CONFORM TO SPECIFICATION JSS: 8305-14 : 2020 (REVISION NO.5) INCLUDING CLAUSE 7.4.2. THE DYNAMIC VISCOSITY OF THE STORE SHOULD BE BETWEEN 10 TO 30 POISE FOR O.F.BHANDARA AGAINST THE DYNAMIC VISCOSITY RANGE 5 TO 50 POISE.

BLANKET COTTON DOSUTI WHITE STITCHED AROUND OF SIZE- 1.5 X 0.8 METER. AS PER SPECIFICATION NO- IS:179-2009 (THIRD REVISION) REAFIRMED-2018.

BLANKET COTTON DOSUTI WHITE STITCHED AROUND OF SIZE- 1.5 X 0.8 METER. AS PER SPECIFICATION NO- IS:179-2009 (THIRD REVISION) REAFIRMED-2018.

• MSME

• BLANKET COTTON DOSUTI WHITE STITCHED AROUND OF SIZE- 1.5 X 0.8 METER. AS PER SPECIFICATION NO- IS:179-2009 (THIRD REVISION) REAFIRMED-2018.

BENZENE SOLVENT SPECN.- IS-534:2007 (FOURTH REVISION).

BENZENE SOLVENT SPECN.- IS-534:2007 (FOURTH REVISION).

• MSME

• BENZENE SOLVENT SPECN.- IS-534:2007 (FOURTH REVISION).

BELLOID T.D. is a Sodium Salt of Condensation Product of Nophthalene Sulphonic acid with Formaldehyde and also called Anionic dispersing agent.

BELLOID T.D. is a Sodium Salt of Condensation Product of Nophthalene Sulphonic acid with Formaldehyde and also called Anionic dispersing agent.

JSS 6810 -145:2017( Revision No 2)

JSS 6810 -145:2017( Revision No 2)

• MSME

• JSS 6810 -145:2017( Revision No 2)

ERDL/DBP/PS 133(a)Sheet No.19 of Sept.1986

ERDL/DBP/PS 133(a)Sheet No.19 of Sept.1986

BAG MADE OF REEL CLOTH AS PER DRG NO.OFBA/NCP/EXPN/17

BAG MADE OF REEL CLOTH AS PER DRG NO.OFBA/NCP/EXPN/17

DRG NO.OFBA/NCP/EXPN/17

• MSME

• BAG MADE OF REEL CLOTH AS PER DRG NO.OFBA/NCP/EXPN/17

GREEN COLOUR/WHITE COLOUR AS PER DRG NO. OFBA/NCP/EXPN/16 DT. 07.6.67

GREEN COLOUR/WHITE COLOUR AS PER DRG NO. OFBA/NCP/EXPN/16 DT. 07.6.67

DRG NO. OFBA/NCP/EXPN/16 DT. 07.6.67

• MSME

• MSME

BAG COTTON CALICO(bleached)FOR NCP 50KG CAPACITY TO DRG.NO. OFBA/NR/251/2, MATERIAL OF CLOTH CALICO BLEACHED CONFORMING TO VARIETY NO.3 OF IS:5088-1982 REAFFIRMED 2017

BAG COTTON CALICO(bleached)FOR NCP 50KG CAPACITY TO DRG.NO. OFBA/NR/251/2, MATERIAL OF CLOTH CALICO BLEACHED CONFORMING TO VARIETY NO.3 OF IS:5088-1982 REAFFIRMED 2017

• MSME

• BAG COTTON CALICO(bleached)FOR NCP 50KG CAPACITY TO DRG.NO. OFBA/NR/251/2, MATERIAL OF CLOTH CALICO BLEACHED CONFORMING TO VARIETY NO.3 OF IS:5088-1982 REAFFIRMED 2017

BAG CAMBRIC 15 KG CAP. AS PER DRG.NO.NEFB/NCP/26 DT 01.07.64 MADE OF CLOTH.CAMBRIC WHITE - VARIETY NO.2 OF IS : 5088-1982 REAFFIRMED1996 AMND1&2(COTTON TEXTILE FOR AMMN)THREAD COTTON WHITE SEWING 16 x 6 UNPROOFED DYED TO JSS-8310-02-1994 DC. NO.3277 DT 21.2 95(REV I) TO BE USED FOR STITCH OF BAG.

BAG CAMBRIC 15 KG CAP. AS PER DRG.NO.NEFB/NCP/26 DT 01.07.64 MADE OF CLOTH.CAMBRIC WHITE - VARIETY NO.2 OF IS : 5088-1982 REAFFIRMED1996 AMND1&2(COTTON TEXTILE FOR AMMN)THREAD COTTON WHITE SEWING 16 x 6 UNPROOFED DYED TO JSS-8310-02-1994 DC. NO.3277 DT 21.2 95(REV I) TO BE USED FOR STITCH OF BAG.

• MSME

• BAG CAMBRIC 15 KG CAP. AS PER DRG.NO.NEFB/NCP/26 DT 01.07.64 MADE OF CLOTH.CAMBRIC WHITE - VARIETY NO.2 OF IS : 5088-1982 REAFFIRMED1996 AMND1&2(COTTON TEXTILE FOR AMMN)THREAD COTTON WHITE SEWING 16 x 6 UNPROOFED DYED TO JSS-8310-02-1994 DC. NO.3277 DT 21.2 95(REV I) TO BE USED FOR STITCH OF BAG.

BAG POLYTHENE FOR PACKING NC- QUALITY OF MATERIAL TO CONFORM TO LOW DENSITY POLYETHYLENE TYPE-1 SPECIFICATION JSS- 9330 - 03-2014,REV.NO.3.THICKNESS 0.18 PLUS MINUS 0.02MM.DIMENSION AND HEAT SEALING AS PER DRG.NO.OFBA/NC/46 AMENDED ON 27.03. 2010.

BAG POLYTHENE FOR PACKING NC- QUALITY OF MATERIAL TO CONFORM TO LOW DENSITY POLYETHYLENE TYPE-1 SPECIFICATION JSS- 9330 - 03-2014,REV.NO.3.THICKNESS 0.18 PLUS MINUS 0.02MM.DIMENSION AND HEAT SEALING AS PER DRG.NO.OFBA/NC/46 AMENDED ON 27.03. 2010.

DRG. NO.OFBA/NC/46 AMENDED ON 27/03/2010.

• MSE

• MSE

DRG. NO. OFBA/RX/243 AMMENDED ON 07/11/02

DRG. NO. OFBA/RX/243 AMMENDED ON 07/11/02

DRG. NO. OFBA/RX/243 AMMENDED ON 07/11/02

• MSME

• BAG COTTON TNT 25 KG TO DRG. NO. OFBA/RX/243 AMMENDED ON 7.11.02.

AMMONIA ANHYDROUS GRADE-2 TO SPECIFICATION IS/662/1980. REAFFIRMED 2003WITH AMENDMENT 1,2,3&4 WITH THE FOLLOWING REQUIREMENTS 1)PURITY 99.5% MIN(2) OIL CONTENT- 0.002% MAXM. AND OTHER PARAMETERS TO CONFIRM TO IS -662-1980 GR-2 (FIRST REVISION) REAFFIRMED-2003 WITH AMENDMENT 1,2,3&4.

AMMONIA ANHYDROUS GRADE-2 TO SPECIFICATION IS/662/1980. REAFFIRMED 2003WITH AMENDMENT 1,2,3&4 WITH THE FOLLOWING REQUIREMENTS 1)PURITY 99.5% MIN(2) OIL CONTENT- 0.002% MAXM. AND OTHER PARAMETERS TO CONFIRM TO IS -662-1980 GR-2 (FIRST REVISION) REAFFIRMED-2003 WITH AMENDMENT 1,2,3&4.

• MSME

• Specn No-IS:662/1980

ALUMINIUM STEARATE TO SPCN:IND/ME-970 :2016. DC-5462-ME-01.6. 2016. (a) Retention on 150 micrometer IS sieve max.5.0%. (b) Retention on 75 micrometer IS sieve max.15%.

ALUMINIUM STEARATE TO SPCN:IND/ME-970 :2016. DC-5462-ME-01.6. 2016. (a) Retention on 150 micrometer IS sieve max.5.0%. (b) Retention on 75 micrometer IS sieve max.15%..

• MSME

• ALUMINIUM STEARATE TO SPCN:IND/ME-970 :2016. DC-5462-ME-01.6. 2016. (a) Retention on 150 micrometer IS sieve max.5.0%. (b) Retention on 75 micrometer IS sieve max.15%.

ALUMINIUM POWDER HEAVY GRADE-I CONFORMING TO SPECIFICATION JSS-1370-03-2014 REVISION NO -3 DC 5297-ME DATED 16.12.2014 HEAVY GRADE SIZE 125 MICROMETER.

ALUMINIUM POWDER HEAVY GRADE-I CONFORMING TO SPECIFICATION JSS-1370-03-2014 REVISION NO -3 DC 5297-ME DATED 16.12.2014 HEAVY GRADE SIZE 125 MICROMETER.

• MSME

• ALUMINIUM POWDER HEAVY GRADE-I CONFORMING TO SPECIFICATION JSS-1370-03-2014 REVISION NO -3 DC 5297-ME DATED 16.12.2014 HEAVY GRADE SIZE 125 MICROMETER.

Drg.No.OFBA/PETN/23 Dtd.15.01.1970

ALUMINIUM CONTAINER AS PER DRG.NO.OFBA/RX/391 Dt 24.10.2020.

ALUMINIUM CONTAINER AS PER DRG.NO.OFBA/RX/391 Dt 24.10.2020.

• MSME

• ALUMINIUM CONTAINER AS PER DRG.NO.OFBA/RX/391 Dt 24.10.2020.

ALKATHENE POLYMER WRM-19 TYPE XD POLYTHENE MOULDING AND EXT RUSION MATERIAL(FOR AMMN. APPLICATION) CONFORMING TO SPECN. DEF/STAN 13-9/1.

ALKATHENE POLYMER WRM-19 TYPE XD POLYTHENE MOULDING AND EXT RUSION MATERIAL(FOR AMMN. APPLICATION) CONFORMING TO SPECN. DEF/STAN 13-9/1.

• MSME

• ALKATHENE POLYMER WRM-19 TYPE XD POLYTHENE MOULDING AND EXT RUSION MATERIAL(FOR AMMN. APPLICATION) CONFORMING TO SPECN. DEF/STAN 13-9/1.

Specn IS/170-2004Fourt revi with purity percent by mass mini 99%

Specn IS/170-2004Fourt revi with purity percent by mass mini 99%

• MSME

• Specn No. IS / 170-2004 (Latest Revision )

HDPE Dot coated Printed Fusible Interlining Fabric 150 cm

1) Raw Material : 100% Cotton 2) Count (Warp & Weft) : 30s 3) Ends per Inch : 76+/- 5 4) Picks per Inch : 76 +/- 5 5) Width : 150 cm (Min) 6) Weave : Plain 7) Coating : HDPE 8) Colour : White 9) GSM : 148 +5/-2.5% 10) Shrinkage % : As per Appendix A of IND/TC/2089(a) 11) Bond Strength (Kgs) : > 2.0 As per IND/TC/2089(a) 12) Packing & Marking : As per CQA(T&C) Kanpur Schedule No. CQA(T&C)/PMS/35(d). Except that : a. Fabric in roll form shall not be less than 40 Mtrs in running length without stitching/ basting in between. b. Roll weight shall not exceed 50 kgs. c. Each roll of fabric shall be wrapped separately with polypropylene plain sheet. final packing of 2 rolls in one W.P Gunny/HDPE sheet. d. Dimension for paper tubes of fabric roll: Outer Diameter-3.5 cm, Inner Diameter-2.5 cm Thickness-0.5 cm. e. Fabric selvedges shall be wound evenly at one edge. 13) Sampling plan : As per annexure.

Sampling Plan attached as Drawing file

CHARGER CLIP 7.62MM AMMUNITION-B

CIA-4205(d), DC No. 36247-A Dtd.26.02.1997 AS PER DRG. NO. CIA/AMMN/411/IQV/18A, DC(I) 35648-A DT. 12-01-1994. SPRING TO DRG. NO. IQV 61, DCI NO. 36790-A DT. 29-10-2001 & SPECN. IS : 2507-1975. CLIP TO DRG. IQV 62, DCI NO. 36790 DT. 29-10-2001 & SPECN. IS : 513-2008. COLD ROLLED LOW CARBON STEEL (V REV.) GRADE DD.

PLASTIC BULLET FOR CARTG. 7.62MM ANTI RIOT

AS PER DRG.NO.

OFV/DC/7.62 PB/001

STEEL SHEET 1.00 MM THICK X (1000 X 2500 MM LONG) TO SPECN IS:5986-2002 GD Fe 410 HOT ROLLED & ANNEALED OR IS:2062-19999 GD Fe410WA OR IS 1079-1988 GD ST42

STEEL SHEET 1.00 MM THICK X (1000 X 2500 MM LONG) TO SPECN IS:5986-2002 GD Fe 410 HOT ROLLED & ANNEALED OR IS:2062-19999 GD Fe410WA OR IS 1079-1988 GD ST42

CUTTING AND STITCHING OF CHARGE BAGS FOR CHARGE 9 OF 155MM AMMN.AS PER DRG.NO-6388103,6388104,6388106,6388115,6388116, 6355588,5191810,5173926,4090246,4090247,4079932. MATERIAL WILL BE SUPPLIED BY OFBA.

CUTTING AND STITCHING OF CHARGE BAGS FOR CHARGE 9 OF 155MM AMMN.AS PER DRG.NO-6388103,6388104,6388106,6388115,6388116, 6355588,5191810,5173926,4090246,4090247,4079932. MATERIAL WILL BE SUPPLIED BY OFBA.

CUTTING AND STITCHING OF CHARGE BAGS FOR CHARGE 9 OF 155MM AMMN.AS PER DRG.NO-6388103,6388104,6388106,6388115,6388116, 6355588,5191810,5173926,4090246,4090247,4079932. MATERIAL WILL BE SUPPLIED BY OFBA.

AS PER HAPP DRG. NO. C PLG 081 1 030

AS PER HAPP DRG. NO. C PLG 081 1 030

IND/TC/4552 (M) & Approved Sample

IND/TC/4552 (M) & Approved Sample

JSPRESS PAHN BOARD DISC THICKNESS 2.0 0.2 MM AND SUBSTANCE 2200 + 110 GRAMS PER SQUARE MTR TO SPECN. JSS: 5970-11,2015(Rev.NO-2).DRG.NO.CI(A) 6388106, DC(I) 34186-A DTD.03.08.87.

PRESS PAHN BOARD DISC THICKNESS 2.0 0.2 MM AND SUBSTANCE 2200 + 110 GRAMS PER SQUARE MTR TO SPECN. JSS: 5970-11,2015(Rev.NO-2).DRG.NO.CI(A) 6388106, DC(I) 34186-A DTD.03.08.87.

DRG.NO.CI(A) 6388106, DC(I) 34186-A DTD.03.08.87.

• MSME

• PRESS PAHN BOARD DISC THICKNESS 2.0 0.2 MM AND SUBSTANCE 2200 + 110 GRAMS PER SQUARE MTR TO SPECN. JSS: 5970-11,2015(Rev.NO-2).DRG.NO.CI(A) 6388106, DC(I) 34186-A DTD.03.08.87.

SPECN-ADRDE/SPCN.2000/54(b)

SPECN-ADRDE/SPCN.2000/54(b)

SPECN.NO:-ADRDE/QMS/TDTM/SPECN/84.

SPECN.NO:-ADRDE/QMS/TDTM/SPECN/84.

Packing of Shell 130MM HE

Packing of Shell 130MM HE as per Terms & Condition as Per Annexure 001/Store Dt. 26.10.2013 Enclosed

PIN CATCH MAGAZINE (THROUGH MIM ROUTE) FOR 9MM AUTO PISTOL. DRG. REF NO. 5315 - 009186 AND DRG NO. RFI. SK. 10120.

PIN CATCH MAGAZINE (THROUGH MIM ROUTE) FOR 9MM AUTO PISTOL. DRG. REF NO. 5315 - 009186 AND DRG NO. RFI. SK. 10120.

DRG. REF NO. 5315 - 009186 AND DRG NO. RFI. SK. 10120.

LEVER SLIDE LOCKING (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003189 AND DRG. NO. RFI SK. 10128

LEVER SLIDE LOCKING (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003189 AND DRG. NO. RFI SK. 10128

DRG. REF. NO. 1005-003189 AND DRG. NO. RFI SK. 10128

PIN ARM (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003203 AND DRG. NO. RFI SK. 10124

PIN ARM (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003203 AND DRG. NO. RFI SK. 10124

DRG. REF. NO. 1005-003203 AND DRG. NO. RFI SK. 10124

HAMMER MK-2 (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

HAMMER MK-2 (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

EQUILIBRATOR ASSY TO DRG. NO. 1015-000413

EQUILIBRATOR ASSY TO DRG. NO. 1015-000413

DRG. NO. 1015-000413

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

B251-800 IPG INTERNAL PIEZO GUAGE

B251-800 IPG INTERNAL PIEZO GUAGE

PART NO.ISV-529A DC NO:37249-A,DT.08.03.10,SPECN:IA 1169(N),DC NO:35576-A, AIDE MEMOIRE- P/11.NOTE-PAINTING AND PROTECTIVE TREATMENT AS PER DRG.PAINTED "OLIVE GREEN"TO ISC NO.220 OF IS-5-2007(SIXTH REVISION) (AMDT.NO.1)(RE-AFFIRMED 2000)

PART NO.ISV-529A DC NO:37249-A,DT.08.03.10,SPECN:IA 1169(N),DC NO:35576-A, AIDE MEMOIRE- P/11.NOTE-PAINTING AND PROTECTIVE TREATMENT AS PER DRG.PAINTED "OLIVE GREEN"TO ISC NO.220 OF IS-5-2007(SIXTH REVISION) (AMDT.NO.1)(RE-AFFIRMED 2000)

CQA(A)/AMN/2608 PT.NO.ISV 529A DC-37249A DT.08/03/10

• SHEARING AND NOTCHING MACHINE SUITABLE PRESS M/C FOR BENDING, FORMING, EMBOSSING/ENGRAVING OPERATION DRILLING MACHINE ARC/GAS WELDING M/C SPOT WELDING M/C PHOSPHATING FACILITY SPRAY PAINTING FACILITY

• SUITABLE MEASURING FACILITY SUITABLE TESTING FACILITY AS PER RELEVANT SPECIFICATION AND DRAWING

DRG.NO.CQA(A)AMN/2644 PART NO.ISV-530A,DC:37249-A,DT.08.3.10 SPECN:IA-1169(n),DC NO:35576-A,PAINTED"OLIVE GREEN"ISC NO: 220 OF IS:5-2007(6TH REVISION) RE AFFIRMED-2012.

DRG.NO.CQA(A)AMN/2644 PART NO.ISV-530A,DC:37249-A,DT.08.3.10 SPECN:IA-1169(n),DC NO:35576-A,PAINTED"OLIVE GREEN"ISC NO: 220 OF IS:5-2007(6TH REVISION) RE AFFIRMED-2012.

PAPER WASHER GLAZED CALENDERED AMMN TO SPCN. JSS 8135-13- 2014 (REV.NO-3) 0.50MM(0.02") THICK OF SIZE 56 MM OD X 36 MM ID.TO DRAWING NO.ERDL DRG 671 DET 9. .

PAPER WASHER GLAZED CALENDERED AMMN TO SPCN. JSS 8135-13- 2014 (REV.NO-3) 0.50MM(0.02") THICK OF SIZE 56 MM OD X 36 MM ID.TO DRAWING NO.ERDL DRG 671 DET 9. .

DRAWING NO.ERDL DRG 671 DET 9. .

PZM NOZZLE CASTING CUM MACHINING LEFT & RIGHT AS PER DRG.NO.FOR LEFT NOZZLE PZM ERDL DRG.NO. 1040, DET-1 AMENDED ON DT.11-03-15,FOR RIGHT NOZZLE PZM ERDL DRG.NO.1040 ,DET-2 AMENDED ON DT.11-03-15 AND FOR CASTING NOZZLE PZM ERDL DRG.NO. 1040.

PZM NOZZLE CASTING CUM MACHINING LEFT & RIGHT AS PER DRG.NO.FOR LEFT NOZZLE PZM ERDL DRG.NO. 1040, DET-1 AMENDED ON DT.11-03-15,FOR RIGHT NOZZLE PZM ERDL DRG.NO.1040 ,DET-2 AMENDED ON DT.11-03-15 AND FOR CASTING NOZZLE PZM ERDL DRG.NO. 1040.

ERDL. DRG NO.1040 DET-1 & ERDL. DRG. NO. 1040 DET-2

• MSME

• PZM NOZZLE CASTING CUM MACHINING LEFT & RIGHT AS PER DRG.NO.FOR LEFT NOZZLE PZM ERDL DRG.NO. 1040, DET-1 AMENDED ON DT.11-03-15,FOR RIGHT NOZZLE PZM ERDL DRG.NO.1040 ,DET-2 AMENDED ON DT.11-03-15 AND FOR CASTING NOZZLE PZM ERDL DRG.NO. 1040.

PAPER WHITE FINE AMMUNITION TO SPECIFICATION JSS-9310-06- 2016. (D.S. CAT NO. 9310-000007) THICKNESS 0.051 PLUS OR MINUS 0.005 MM AND SIZE 762 X 508 MM.

PAPER WHITE FINE AMMUNITION TO SPECIFICATION JSS-9310-06- 2016. (D.S. CAT NO. 9310-000007) THICKNESS 0.051 PLUS OR MINUS 0.005 MM AND SIZE 762 X 508 MM.

• MSME

• PAPER WHITE FINE AMMUNITION TO SPECIFICATION JSS-9310-06- 2016. (D.S. CAT NO. 9310-000007) THICKNESS 0.051 PLUS OR MINUS 0.005 MM AND SIZE 762 X 508 MM.

PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.

PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.

PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.

• MSME

• PAPER LINER FOR PACKING 68 MM ARROW CHARGES AS PER SPECN. IA/918 C-(g) DC (I) 33749-A AND DRG.NO.ARM-1503-C.