SUPPLY OF CO2 GAS CYLINDER ON REQUIREMENT AND REPLACEMENT BASIS,(EMPTY CYLINDERS WILL BE TAKEN BY THE FIRM AND FILLED CLYLINDERS WILL BE SUPPLIED BY THE FIRM)
Specification
SUPPLY OF CO2 GAS CYLINDER ON REQUIREMENT AND REPLACEMENT BASIS,(EMPTY CYLINDERS WILL BE TAKEN BY THE FIRM AND FILLED CLYLINDERS WILL BE SUPPLIED BY THE FIRM)
Drawing no.
Manufacturing Technology
SUPPLY OF CO2 GAS CYLINDER ON REQUIREMENT AND REPLACEMENT BASIS,(EMPTY CYLINDERS WILL BE TAKEN BY THE FIRM AND FILLED CLYLINDERS WILL BE SUPPLIED BY THE FIRM)
GLYCERINE FOR NITRATION TO SPECN.NO. JSS-6810-109:2013 REVISION NO 3, DC 5219-ME DTD.12.04.14. ALONGWITH SULPHURIC ACID COLOURATION TEST. THE GLYCERINE MUST PASS THROUGH THE SULPHURIC ACID COLOURATION TEST.
Specification
GLYCERINE FOR NITRATION TO SPECN.NO. JSS-6810-109:2013 REVISION NO 3, DC 5219-ME DTD.12.04.14. ALONGWITH SULPHURIC ACID COLOURATION TEST. THE GLYCERINE MUST PASS THROUGH THE SULPHURIC ACID COLOURATION TEST.
GLYCERINE FOR NITRATION TO SPECN.NO. JSS-6810-109:2013 REVISION NO 3, DC 5219-ME DTD.12.04.14. ALONGWITH SULPHURIC ACID COLOURATION TEST. THE GLYCERINE MUST PASS THROUGH THE SULPHURIC ACID COLOURATION TEST.
EXPANDED CROSS LINKED POLYETHYLENE FOAM BASED CUSHIONING MATERIAL FOR PACKING OF AMMUNITION AS PER SPECIFICATION No.IND/ME/1023 (PROV),DC No.5111-ME DATED : 27/04/2013.
Specification
EXPANDED CROSS LINKED POLYETHYLENE FOAM BASED CUSHIONING MATERIAL FOR PACKING OF AMMUNITION AS PER SPECIFICATION No.IND/ME/1023 (PROV),DC No.5111-ME DATED : 27/04/2013.
EXPANDED CROSS LINKED POLYETHYLENE FOAM BASED CUSHIONING MATERIAL FOR PACKING OF AMMUNITION AS PER SPECIFICATION No.IND/ME/1023 (PROV),DC No.5111-ME DATED : 27/04/2013.
STRONG NITRIC ACID CONFORMING TO IS:264:2005(Reaffirmed Year : 2017 ) EXPLOSIVE GR.WITH SPECIFIC REQURIMENET TO FOLLOWING CLAUSES OF TABLE-I CLAUSE 4.2 TOTAL ACIDITY (AS HNO3)% BY MASS MINIMUM 98.5% NITRIOUS ACID MAX 0.08% BY MASS(AS HNO2) SULPHATE NOT MORE THAN 0.2%.
Specification
STRONG NITRIC ACID CONFORMING TO IS:264:2005(Reaffirmed Year : 2017 ) EXPLOSIVE GR.WITH SPECIFIC REQURIMENET TO FOLLOWING CLAUSES OF TABLE-I CLAUSE 4.2 TOTAL ACIDITY (AS HNO3)% BY MASS MINIMUM 98.5% NITRIOUS ACID MAX 0.08% BY MASS(AS HNO2) SULPHATE NOT MORE THAN 0.2%.
STRONG NITRIC ACID CONFORMING TO IS:264:2005(Reaffirmed Year : 2017 ) EXPLOSIVE GR.WITH SPECIFIC REQURIMENET TO FOLLOWING CLAUSES OF TABLE-I CLAUSE 4.2 TOTAL ACIDITY (AS HNO3)% BY MASS MINIMUM 98.5% NITRIOUS ACID MAX 0.08% BY MASS(AS HNO2) SULPHATE NOT MORE THAN 0.2%.
GROUND STEEL ROD TO SPECIFICATION IS: 5517 GR 40Ni6Cr4Mo3 IN HARDENED CONDITION TO SIZE DIA 11MM+/-0.05MM IN STRAIGHT LENGTH OF 2 TO 3 METERS. HARDNESS – 300 to 340HV
Specification
GROUND STEEL ROD TO SPECIFICATION IS: 5517 GR 40Ni6Cr4Mo3 IN HARDENED CONDITION TO SIZE DIA 11MM+/-0.05MM IN STRAIGHT LENGTH OF 2 TO 3 METERS. HARDNESS – 300 to 340HV
GROUND STEEL ROD TO SPECIFICATION IS:5517 GR 40Ni6Cr4Mo3 IN HARDENED CONDITION TO SIZE DIA 17MM+/-0.05MM IN STRAIGHT LENGTH OF 2 TO 3 METERS.HARDNESS – 300 to 340HV
Specification
GROUND STEEL ROD TO SPECIFICATION IS:5517 GR 40Ni6Cr4Mo3 IN HARDENED CONDITION TO SIZE DIA 17MM+/-0.05MM IN STRAIGHT LENGTH OF 2 TO 3 METERS.HARDNESS – 300 to 340HV
Manufacturing Facilities Involved
• CNC /Conventional machining or Metal Forming –Press Work.
• Blanking/laser Cut if Metal Forming –Press Work.
In case the tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The machining Facility is mandatory.
Inspection Facilities Involved
• Standard Measuring Instruments & Gauges
• Material Testing Facility with NABL Accreditation
Tenderer shall satisfy / declare the required inspection facilities are available either in-house or outsourced.
71
256 NUMBERS
Number
5207
2019000129
Ordnance Clothing Factory Shahjahanpur
The General Manager,
Shahjahanpur
Shahjahanpur
Shahjahanpur, Uttar Pradesh
242001
100% Nylon PU coated water proof and wind proof breathable plain weave fabric 100 GSM OG width 150 cm (min.)
Specn:- Appendix "A" of Provisional Specification No. OCFS/039/Jacket ECC Two Layer
Specification
100% Nylon PU coated water proof and wind proof breathable plain weave fabric 100 GSM OG width 150 cm (min.)
Specn:- Appendix "A" of Provisional Specification No. OCFS/039/Jacket ECC Two Layer
Drawing no.
Manufacturing Technology
as per attached list (Manufacturing Technology Files )
CLOTH CEE HEAVY 72 CM (C.N.H2/8305)
CLOTH CEE HEAVY 72 CM (CAT PART NO. H2/8305-000142)
SPECIFICATION: IS:3751-1993 (FIRST REVISION) REAFFIRMED 2010 AMD. NO. 1
Specification
CLOTH CEE HEAVY 72 CM (C.N.H2/8305)
CLOTH CEE HEAVY 72 CM (CAT PART NO. H2/8305-000142)
SPECIFICATION: IS:3751-1993 (FIRST REVISION) REAFFIRMED 2010 AMD. NO. 1
Drawing no.
Manufacturing Technology
as per attached list (Manufacturing Technology Files )
COLOURLESS, TRANSIT PLUG TO DRG NO. RW142/SK/0808/E DT 20-02-2004 AMENDED UPTO 05.11.2016 FOR CASE CARTG 105MM IFG TO SPECN.JSS-9330-03-2014 REVISION NO.3, L.D.PE. GRADE, TYPE 2.
Specification
SPECN.JSS-9330-03-2014 REVISION NO.3, L.D.PE. GRADE, TYPE 2.
STEEL FLAT RECTANGULAR SIZE (40+5)MMX(65+5)MM IN THE LENGTH OF 1.5 TO 3MTR TO SPECN. BS:970 PT1 1983,GR 817 M40 HOT ROLLED AND NORMALISED CONDITION.TEST PIECE HARDNESS TO ACHIEVE 425-475 HV.
Specification
STEEL FLAT RECTANGULAR SIZE (40+5)MMX(65+5)MM IN THE LENGTH OF 1.5 TO 3MTR TO SPECN. BS:970 PT1 1983,GR 817 M40 HOT ROLLED AND NORMALISED CONDITION.TEST PIECE HARDNESS TO ACHIEVE 425-475 HV.
POLY FILL (100 % POLYESTER) 100 GSM WITH PRE-QUILTED NON-WOVEN WEB LINING WIDTH 150 CM MIN.
Specification - APPENDIX 'D' OF PROVISIONAL SPECIFICATION NO. OCFS/039/JACKET ECC TWO LAYER
Specification
POLY FILL (100 % POLYESTER) 100 GSM WITH PRE-QUILTED NON-WOVEN WEB LINING WIDTH 150 CM MIN.
Specification - APPENDIX 'D' OF PROVISIONAL SPECIFICATION NO. OCFS/039/JACKET ECC TWO LAYER
Drawing no.
Manufacturing Technology
as per attached list (Manufacturing Technology Files )
IND/ADE/0087 (a) Except That
1-Weight, gsm – A tolerance of +-10% shall be applicable to 407 gsm after waterproofing.
2-Count of yarn :-Warp :-2 ply of 20s Single yarn
Weft :-3 ply of 24s Single yarn
(Note: The count of single yarn is approximate and given for the guidance of the manufacturers. The no. of plies, however, shall not be changed.)
3-No. of threads/ inch:- Warp:-92 Weft:-48
(The tolerance in no. of threads/inch shall be +- 5%)
4-Shade OD (Olive Drab), Shade No. 298 as per IS:5
SPIRIT DENATURED SPECIAL PREPARED USING RECTIFIED SPIRIT TO IS 323-2009 REVISED (Reaffirmed - 2019) WITH ACIDITY NOT EXCEEDING 0.005% AND ALDEHYDE CONTENT 0.0 06 G/100 ML MAX. DENATURED WITH 1% DIETHYL ETHER TO IS 336 : 1973 (REAFFIRMED 2018) Revision 2 .
Specification
SPIRIT DENATURED SPECIAL PREPARED USING RECTIFIED SPIRIT TO IS 323-2009 REVISED (Reaffirmed - 2019) WITH ACIDITY NOT EXCEEDING 0.005% AND ALDEHYDE CONTENT 0.0 06 G/100 ML MAX. DENATURED WITH 1% DIETHYL ETHER TO IS 336 : 1973 (REAFFIRMED 2018) Revision 2 .
SPIRIT DENATURED SPECIAL PREPARED USING RECTIFIED SPIRIT TO IS 323-2009 REVISED (Reaffirmed - 2019) WITH ACIDITY NOT EXCEEDING 0.005% AND ALDEHYDE CONTENT 0.0 06 G/100 ML MAX. DENATURED WITH 1% DIETHYL ETHER TO IS 336 : 1973 (REAFFIRMED 2018) Revision 2 .
POTASSIUM NITRATE GRADE I FOR EXPLOSIVE AND PYROTECHNIC COMPOSITION TO SPECN IS:301-1982 (SECOND REVISION) REAFFIRMED 2016 AMDS 1 DC NO 3810 ME DTD 5-5-04 SIZE ALL PASSING THROUGH 125 MICROMETER I S SIEVE.
Specification
POTASSIUM NITRATE GRADE I FOR EXPLOSIVE AND PYROTECHNIC COMPOSITION TO SPECN IS:301-1982 (SECOND REVISION) REAFFIRMED 2016 AMDS 1 DC NO 3810 ME DTD 5-5-04 SIZE ALL PASSING THROUGH 125 MICROMETER I S SIEVE.
FORMULA-C6H10N8O4, MOLECULAR WT. IN TERMS OF ATOMIC WT. IN 1971 IS 258.198, DETAILS PHYSICAL AND CHEMICAL PARAMETER’S ATTACHED AS PER RUSSIAN SPECIFICATION TU 30 E 2015
Specification
FORMULA-C6H10N8O4, MOLECULAR WT. IN TERMS OF ATOMIC WT. IN 1971 IS 258.198, DETAILS PHYSICAL AND CHEMICAL PARAMETER’S ATTACHED AS PER RUSSIAN SPECIFICATION TU 30 E 2015
FORMULA-C6H10N8O4, MOLECULAR WT. IN TERMS OF ATOMIC WT. IN 1971 IS 258.198, DETAILS PHYSICAL AND CHEMICAL PARAMETER’S ATTACHED AS PER RUSSIAN SPECIFICATION TU 30 E 2015
STRONG NITRIC ACID CONFORMING TO IS:264:2005(Reaffirmed Year : 2017 ) EXPLOSIVE GR.WITH SPECIFIC REQURIMENET TO FOLLOWING CLAUSES OF TABLE-I CLAUSE 4.2 TOTAL ACIDITY (AS HNO3)% BY MASS MINIMUM 98.5% NITRIOUS ACID MAX 0.08% BY MASS(AS HNO2) SULPHATE NOT MORE THAN 0.2%.
Specification
STRONG NITRIC ACID CONFORMING TO IS:264:2005(Reaffirmed Year : 2017 ) EXPLOSIVE GR.WITH SPECIFIC REQURIMENET TO FOLLOWING CLAUSES OF TABLE-I CLAUSE 4.2 TOTAL ACIDITY (AS HNO3)% BY MASS MINIMUM 98.5% NITRIOUS ACID MAX 0.08% BY MASS(AS HNO2) SULPHATE NOT MORE THAN 0.2%.
STRONG NITRIC ACID CONFORMING TO IS:264:2005(Reaffirmed Year : 2017 ) EXPLOSIVE GR.WITH SPECIFIC REQURIMENET TO FOLLOWING CLAUSES OF TABLE-I CLAUSE 4.2 TOTAL ACIDITY (AS HNO3)% BY MASS MINIMUM 98.5% NITRIOUS ACID MAX 0.08% BY MASS(AS HNO2) SULPHATE NOT MORE THAN 0.2%.
Manufacturing Facilities Involved
• CNC /Conventional machining or Metal Forming –Press Work.
• Blanking/laser Cut if metal forming –Press Work.
In case the tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The machining Facility is mandatory.
Inspection Facilities Involved
• Standard Measuring Instruments & Gauges
• Material Testing Facility with NABL Accreditation
Tenderer shall satisfy / declare the required inspection facilities are available either in-house or outsourced.
1. Blast Furnace with LD Converter (Basic Oxygen Furnace) OR Electric ARC
Furnace OR Induction
Furnace.
2. Firm should be able to supply minimum 500 to 650 nos. of parted steel
billets per heat batch.
3. Ladle Refining furnace along with Argon purging system.
4. Vacuum degassing furnace along with Argon purging system.
5. Continuous caster OR Bottom pouring ingot casting facilities.
6. Soaking Pits OR Pre heating Furnace.
7. Rolling Mill to maintain reduction ratio of at least 6:1.
8. Annealing OR Normalising Furnace
9. Optical emission Spectrometer.
10. Carbon Sulphur Analyzer.
11. Temperature measuring facilities during melting/ casting.
12. Mechanical test facilities, as applicable.
13. Metallography facilities for Micro and Macro Analysis.
14. Ultrasonic Testing facilities with qualified personnel.
B) Desirable Eligibility Criteria:
Firm should have successfully executed supply orders for similar calibre
ammunition in past. Supply
order copies to be attached/ uploaded along with TE
