Chemical & Mechanical properties as per std. given drawing /Specification.
2) Dimensional inspection for all dimension given in the drawing & other parameter which are mentioned in relevant drawing/specification
70
3
Number
5602
TE NO 190401P2FO
Gun Carriage Factory
The General Manager,
Jabalpur
Jabalpur
Jabalpur,Madhya Pradesh
482011
Following test as per Drg./QAP/Spec
1. Phosphate coating thickness
2. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
3. Thread gauge, Radius gauge
"Firm Should have the following in-house facility or arrange from outside and necessary tie up letter to be submitted.
i.e. Firm should have Chemical, Metallurgical & Mechanical testing Laboratory or tie up with other firms for the same."
"Firm Should have the following in-house facility or arrange from outside and necessary tie up letter to be submitted.
i.e. Firm should have Galvanizing & Chromatizing Facility or tie up with other firms for the same."
"Firm should have the following in-house manufacturing facilities for manufacturing of the item.
Milling Machine (Essential Criteria)"
"Firm should have the following in-house manufacturing facilities for manufacturing of the item.
Lathe Machine (Essential Criteria)"
"Firm should have the following in-house manufacturing facilities for manufacturing of the item.
Forging Facility-Open Die forging 500 Ton minimum capacity (Essential Criteria)"
"Firm Should have the following in-house facility or arrange from outside and necessary tie up letter to be submitted.
i.e. Firm should have Chemical, Metallurgical & Mechanical testing Laboratory or tie up with other firms for the same."
"Firm Should have the following in-house facility or arrange from outside and necessary tie up letter to be submitted.
i.e. Firm should have Galvanizing & Chromatizing Facility or tie up with other firms for the same."
Inspection Technology:
Following test as per Drg./QAP/Spec
1. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
i) Rubber Moulding
ii) Die making
In case tenderer is outsourcing any/some of the above activities, copy of the agreement with such source shall be submitted. The Rubber moulding facility is mandatory
(i) Standard Measuring Instruments & Gauges
(ii) Rubber Testing Facility with NABL/IRMRA accreditation
Tenderer shall satisfy /declare the required inspection facilities are available either in house or outsourced
i) Foundry Facility for Steel Casting
ii) Heat Treatment Facility
iii) Conventional/CNC machining
iv) Surface Treatment
In case tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The machining facility is mandatory.
(i) Measuring Instruments/CMM & Gauges
(ii) Radiography Testing Facility duly certified by Government
(iii) Material Chemical & Physical facility with NABL accreditation
Tenderer shall satisfy /declare the required inspection facilities are available either in house or outsourced.
(i)Conventional /CNC machining Facility
(ii) Grinding Facility
In case tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The machining facility is mandatory
(i) Standard Measuring Instruments & Gauges
(ii)Material Chemical & Physical facility with NABL accreditation
Tenderer shall satisfy /declare the required inspection facilities are available either in house or outsourced
(i) Heat treatment Facility
(ii) Coventional/CNC Machining
(iii)Grinding
iv) Surface Treatment Facility
v) Hard Chrome Plating
vi) Nitriding
vi) Gear Cutting
In case tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The machining facility is mandatory
(i) Measuring Instruments/CMM & Gauges
(ii) Material Chemical & Physical facility with NABL accreditation
Tenderer shall satisfy /declare the required inspection facilities are available either in house or outsourced
i)Heat Treatment facility
ii) Conventional/CNC machining
iii) Welding
iv) Surface Treatment facility
In case tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The machining facility is mandatory
i) Measuring Instruments/CMM & Gauges
ii) Material Chemical & Physical facility with NABL accreditation
Tenderer shall satisfy /declare the required inspection facilities are available either in house or outsourced
1. Chemical & Mechanical properties as per std. given drawing.
2. Dimensional inspection, for all dimensions given in the drawing & other parameter which are mentioned in relevant drawing.
PLASTIC SLIDE FASTENER OPEN END MEDIUM SPECIAL DUTY WHITE 58CM. SPECIFICATION:- IS:14181(PART 1-3) 2002 REAFFIRMED-2013.AS PER RELEVANT CLAUSE OF SPECIFICATION.AS PER RELEVANT CLAUSE OF SPECIFICATION
Specification
PLASTIC SLIDE FASTENER OPEN END MEDIUM SPECIAL DUTY WHITE 58CM. SPECIFICATION:- IS:14181(PART 1-3) 2002 REAFFIRMED-2013.AS PER RELEVANT CLAUSE OF SPECIFICATION.AS PER RELEVANT CLAUSE OF SPECIFICATION
Drawing no.
Manufacturing Technology
as per attached list (Manufacturing Technology Files )
(i) Foundry Facility for Aluminium Casting
(ii) Heat Treatment Facility
(iii) Conventional/CNC machining
(iv) Surface Treatment
In case tenderer is outsourcing any/some of the above activities, copy of agreement with such source shall be submitted. The foundry facility is mandatory.
(i) Measuring Instruments/CMM & Gauges
(ii) Radiography Testing facility duly certified by the Government
(iii) Material Chemical & Physical facility with NABL accreditation
Tenderer shall satisfy /declare the required inspection facilities are available either in house or outsourced.
71
8
Set
5611
EOI/PROVISIONAL/REGULARIZATION
Ordnance Equipment Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208001
1) Measuring Instruments/CMM & Gauges
2) Radiography Testing facility duly certified by the Government
3) Material Chemical & Physical facility with NABL accreditation
PAPER & BOARD CORRUGATED AMMUNITION DOUBLE FACED FINE FLUTE TO SPECN NO. JSS:8135-08:2008 (REV. NO.3)CONFIRMING TO STD SIZE- 787 MM X 559 MM X 5 MM THICK.
Specification
PAPER & BOARD CORRUGATED AMMUNITION DOUBLE FACED FINE FLUTE TO SPECN NO. JSS:8135-08:2008 (REV. NO.3)CONFIRMING TO STD SIZE- 787 MM X 559 MM X 5 MM THICK.
Inspection Technology:
Following test as per Drg./QAP/Spec
1. GSM testing facility
2.Chemical testing facility (Moisture content,PH of water extract, Water soluble chloride, Water
soluble sulphate, Fatty acids, Ash content%, Matter soluble in ether)
Inspection Technology:
Following test as per Drg./QAP/Spec
1. n-heptane test
2. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
Inspection Technology:
Following test as per Drg./QAP/Spec
1. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
Inspection Technology:
Following test as per Drg./QAP/Spec
1. Specific gravity
2. Flash point
3. Lead %
4. Evaporation %
5.PH of water extract
6. Water soluble chlorides
7. Water soluble sulphates
8. compatibility with explosive
9. Penetration.
CONNECTOR NO. CA 3981 FOR DETONATOR CABLE ELECTRIC 1B/L TODRG. PART NO. IQX 165 GF DC NO. 36953-A DT.10-03-04 ANDPVC SLEEVE INTERNAL DIAMETER 3.00 MM AND LENGTH 25 TO 30 MM
Specification
CONNECTOR NO. CA 3981 FOR DETONATOR CABLE ELECTRIC 1B/L TODRG. PART NO. IQX 165 GF DC NO. 36953-A DT.10-03-04 ANDPVC SLEEVE INTERNAL DIAMETER 3.00 MM AND LENGTH 25 TO 30 MM
Inspection Technology:
Following test as per Drg./QAP/Spec
1. Continuity test
2. General purpose engineering equipment to measure dimensions like Micrometer, Vernier Caliper,
Height Gauge.
The Tape shall be in continuous length of 110 M (Excluding Sampling) Without Any Flag Otherwise That Roll Be Treated As Short Length.
ADRDE/QMS/TGTE/T/2019/02 Date: 10/05/2019
1. Electrical non-conductivity of pins
2. Plating thickness
3. Non-conductivity test
4. n-heptane test
5.Thread gauge
6. General Engineering Equipment for measurement
Inspection Technology
1. Non continuity test (Multimeter)
2. Air tightness Test
3. n-heptane test
4. Water Leakage test
5.Plating Thickness
6. General Engineering Equipment for measurement
PACKING BOX FOR SHAPED CHARGE 90MM CONSISTING OF10 COMPONENTS TO DRG NO. HE/CAST 086 DET 1 TO 10(EXCLUDING 90MM SHAPED CHARGE & SET OF LEGS) & QAP NO. HEMRL/HE/ADD/08/01 REV. 00 OF 09/2008
Specification
PACKING BOX FOR SHAPED CHARGE 90MM CONSISTING OF10 COMPONENTS TO DRG NO. HE/CAST 086 DET 1 TO 10(EXCLUDING 90MM SHAPED CHARGE & SET OF LEGS) & QAP NO. HEMRL/HE/ADD/08/01 REV. 00 OF 09/2008
1. Timber processing Unit (Cutting, Finishing,Polishing,Painting)
2. Pressure impregnation plant for preservative treatment (As per specification IA 948)
SECONDRY REFIND AOD/VOD QUALITY STEEL ROD 46 MM DIA CONFORMING G TO THE SPECIFICTION JSS 9510-06:2000 (REV NO.3)CODE REF "B" IN HOT ROLLED,ANNEALED AND PEELED CONDT. IN MULTIPLE OF 413MM LENGTH TEST PIECETO BE TESTED IN T-1 CONDTION.MACROET- CH TESTING TO CON IS 13015:1991 & NMIR TEST (ANNEXURE-A ENCL)
Specification
SECONDRY REFIND AOD/VOD QUALITY STEEL ROD 46MM DIA CONFORMING G TO THE SPECIFICTION JSS 9510-06:2000 (REV NO.3)CODE REF "B" IN HOT ROLLED,ANNEALED AND PEELED CONDT. IN MULTIPLE OF 413MM LENGTH TEST PIECETO BE TESTED IN T-1 CONDTION.MACROET- CH TESTING TO CON IS 13015:1991 & NMIR TEST (ANNEXURE-A ENCL)
MINE DRILL APERS M14 WITH FZ INTGL(E) ASS.& PKD IN APPD.PKG.5RG ITX 14GA DC 36985A/14-10-04,SPCN.CQA(A)1828(C) DC 37095A/27-2-07.PKD AMN 70B/L DRG ISV 221GA DC36250A/4-3-97SPCN PKGIA948(A,K)DC 36868A/29-11-02,MKG.& PTG.CRATE 2A BY LAT.DRGORCIA/AMN/STENCIL/77,DSCAT8140-0000,CIA/AMN/610 TO ISV 309A
Specification
MINE DRILL APERS M14 WITH FZ INTGL(E) ASS.& PKD IN APPD.PKG.5RG ITX 14GA DC 36985A/14-10-04,SPCN.CQA(A)1828(C) DC 37095A/27-2-07.PKD AMN 70B/L DRG ISV 221GA DC36250A/4-3-97SPCN PKGIA948(A,K)DC 36868A/29-11-02,MKG.& PTG.CRATE 2A BY LAT.DRGORCIA/AMN/STENCIL/77,DSCAT8140-0000,CIA/AMN/610 TO ISV 309A
Drawing no.
Manufacturing Technology
1. Injection Moulding
2. Galvanizing & chromate passivation as per specification
3. Heat Treatment
4. Pressurized Preservative impregnation plant (As per specification IA948)
Testing / Inspection Facility
1. n-heptane/Glacial acetic acid test as per specification
2. Spring load test
3. Rust proof test as per specn
4. General purpose engineering equipment’s to measure dimensions like Micrometre, vernier caliper, Height gauge.
5. Thread gauge
6. Jolt drop for wood packaging.
7. Depth of penetration for wood preservative.
BOOSTER SUB ASSEMBLY WITH SET BACK MECHANISM TO CQA(A) DRG. NO.13021-0-0.DC(I). NO.35218-A DT.13-11-91. WITH CUP BOOSTER TO CQA(A) DRG.NO.13032-0-0.DC(I). NO.36804-A DT.1-1-02.SPECN. NO. MIL-F-46996 B(MU),AIDEMEMOIRE B/14 AND CQA(A)PROOF SCHEDULE NO. CQA (A)/PS/FZ/120/5 (PROVISIONAL)
Specification
BOOSTER SUB ASSEMBLY WITH SET BACK MECHANISM TO CQA(A) DRG. NO.13021-0-0.DC(I). NO.35218-A DT.13-11-91. WITH CUP BOOSTER TO CQA(A) DRG.NO.13032-0-0.DC(I). NO.36804-A DT.1-1-02.SPECN. NO. MIL-F-46996 B(MU),AIDEMEMOIRE B/14 AND CQA(A)PROOF SCHEDULE NO. CQA (A)/PS/FZ/120/5 (PROVISIONAL)
Drawing no.
BOOSTER SUB ASSEMBLY WITH SET BACK MECHANISM TO CQA(A) DRG. NO.13021-0-0.DC(I). NO.35218-A DT.13-11-91
1. Chemical & Mechanical properties as per std. given drawing.
2. Dimensional inspection, for all dimensions given in the drawing & other parameter which are mentioned in relevant drawing.
