PAINT READYMIXED(MIDDLE BUFF) AIR DRYING SEMI GLOSSY, TYPE-BRUSHING CONSISTENCY TO SPECN: IS-168-REAFFIRMED 2012 APPLICABLE FOR DEFENCE USE & COLOUR SHADEISC NO.359 OF IS: 5-2007(6TH REVISION) AMENDMENT NO.1.(TO BE SUPPLIED IN 5 LTRS PACK)

PAINT READYMIXED(MIDDLE BUFF) AIR DRYING SEMI GLOSSY, TYPE-BRUSHING CONSISTENCY TO SPECN: IS-168-REAFFIRMED 2012 APPLICABLE FOR DEFENCE USE & COLOUR SHADEISC NO.359 OF IS:5-2007(6TH REVISION) AMENDMENT NO.1.(TO BE SUPPLIED IN 5 LTRS PACK)

PAINT R/M AIRDRYING MATT ORTHOXYLENE BASED ZINC CHROME RED OXIDE TO SPECN.IND/ ME/ 964(PROV), DCI 5262-ME, DT-24.06.14,MODE OF APPLICATION-SPRAYING/ BRUSHING/ DIPPING/ POUR, FOR INNER COATING OF HE. SHELL. [TO BE SUPPLIED IN 500ML PACK] ADDITIONAL REQUIREMENT:- THE ENCLOSED TEST PARAMETERS TO BE ENSURED,BY TESTING THE ADVANCE SAMPLE BEFORE BULK SUPPLY.THERE WILL BE A COMPARATIVE TEST OF ADVANCE SAMPLE & THAT OF THE SAMPLE DRAWN FROM THE BULK SUPPLY IN CASE OF ADVANCE SAMPLE IS ACCEPTED. TEST PARAMETERS ARE ENCLOSED.

PAINT R/M AIRDRYING MATT ORTHOXYLENE BASED ZINC CHROME RED OXIDE TO SPECN.IND/ ME/ 964(PROV), DCI 5262-ME, DT-24.06.14,MODE OF APPLICATION-SPRAYING/ BRUSHING/ DIPPING/ POUR, FOR INNER COATING OF HE. SHELL. [TO BE SUPPLIED IN 500ML PACK] ADDITIONAL REQUIREMENT:- THE ENCLOSED TEST PARAMETERS TO BE ENSURED,BY TESTING THE ADVANCE SAMPLE BEFORE BULK SUPPLY.THERE WILL BE A COMPARATIVE TEST OF ADVANCE SAMPLE & THAT OF THE SAMPLE DRAWN FROM THE BULK SUPPLY IN CASE OF ADVANCE SAMPLE IS ACCEPTED. TEST PARAMETERS ARE ENCLOSED.

PARANITRO TOLUENE TO SPECN.IND/ME/962 (PROV) DC-3284-ME, DT-21.02.95.

PARANITRO TOLUENE TO SPECN.IND/ME/962 (PROV) DC-3284-ME, DT-21.02.95.

X-RAY CHEMICALS COMPRISING OF AUTO PROCESSOR DEVELOPER AND AUTO PROCESSOR FIXER FOR INDUSTRIAL USE (TO BE SUPPLIED AS A SET FOR PREPARING HOMOGENOUS SOLUTION OF 20 LITRES DEVELOPER AND 25 LITRES FIXER AND DETAILS OF CONSTITUENTS TO BE MENTIONED).

X-RAY CHEMICALS COMPRISING OF AUTO PROCESSOR DEVELOPER AND AUTO PROCESSOR FIXER FOR INDUSTRIAL USE (TO BE SUPPLIED AS A SET FOR PREPARING HOMOGENOUS SOLUTION OF 20 LITRES DEVELOPER AND 25 LITRES FIXER AND DETAILS OF CONSTITUENTS TO BE MENTIONED).

X-RAY FILM ROLL, WIDTH-17"x 200 FEET LENGTH, FILM SPEED-100. DIMENSION OF PAPER CYLINDER ON WHICH FILMS TO BE ROLLED: ID = 77+/-2.0 MM, OD = 90.0 MM MAX., LENGTH = 430+/-10.0 MM AND OVERALL OD OF X-RAY FILM ROLL = 150MM MAX.

X-RAY FILM ROLL, WIDTH-17"x 200 FEET LENGTH, FILM SPEED-100. DIMENSION OF PAPER CYLINDER ON WHICH FILMS TO BE ROLLED: ID = 77+/-2.0 MM, OD = 90.0 MM MAX., LENGTH = 430+/-10.0 MM AND OVERALL OD OF X-RAY FILM ROLL = 150MM MAX.

• AS PER STANDARD NORM

• TEST CERTIFICATE AND TEST IN BUYER SITE

DRG. No.155-1070, DC No.36792-A, Dt.01.11.2001 (SPECIAL REQUIREMENT HEIGHT SHOULD BE 33.7 - 0.5 MM)

DRG. No.155-1070, DC No.36792-A, Dt.01.11.2001 (SPECIAL REQUIREMENT HEIGHT SHOULD BE 33.7 - 0.5 MM)

OBTURATOR TO DESIGNER REF.NO.155- 1140,DC NO.37025-A,DT.08.08.2005.

OBTURATOR TO DESIGNER REF.NO.155- 1140,DC NO.37025-A,DT.08.08.2005.

SCUFF PROTECTOR TO DRG.NO:155-1110 DC NO.37025-A,DT.08.08.05.

SCUFF PROTECTOR TO DRG.NO:155-1110 DC NO.37025-A,DT.08.08.05.

GRUMMET ASSY CONSISTING OF (1)GRUMMET 155MM (2) RING (3) PIN ASSEMBLY FOR SHELL 155MM ERFB/BB & BT TO DESIGNER'S REF.NO:04-13-2452-148. (REF.OFBL DRG.NO: BL/PB/U-5/343)..

GRUMMET ASSY CONSISTING OF (1)GRUMMET 155MM (2) RING (3) PIN ASSEMBLY FOR SHELL 155MM ERFB/BB & BT TO DESIGNER'S REF.NO:04-13-2452-148. (REF.OFBL DRG.NO: BL/PB/U-5/343)..

MOP 12 SHELLS 155MM BT ON PELLET WITHOUT GRUMET TO DRG.NO:155-1000(M)(UNIT LOAD)CONSISTING OF PALLET TO DRG.NO.155-1210(M), FRAME ASSEMBLY TO DRG.NO.155-1230(M) DC NO.37126-A,DT.25.7.07.

AS PER DRAWING / SPECIFICATIONS

EYELET ALUMINIUM ALLOY CHEMICALLY PASSIVATED WITH WASHER NO.21

SPECN- EYELET ALUMINIUM ALLOY WITH WASHER NO.21 CONFIRMING TO IS:4084-78 WITH amdt. NO.1 & SUPPLEMENTARY SCHEDULE NO. CQA(GS)/SS/335

BATTERY SECONDARY LEAD ACID 12V 120AH AT 5 HRS RATE WITH SIDE TERMINAL PROTECTOR TOP COVER DRG NO CQAL 4429B DS CAT NO LV6 MT4 6140 005117 SPEC CQAL 637 C 2014

BATTERY SECONDARY LEAD ACID 12V 120AH AT 5 HRS RATE WITH SIDE TERMINAL PROTECTOR TOP COVER DRG NO CQAL 4429B DS CAT NO LV6 MT4 6140 005117 SPEC CQAL 637 C 2014

ST.SQR.65MMX2.50MTR LONG OR MULTIPLE TO SPEC.BS:3S144-1995 (1999)GD.S144 D LFVD(WITH CAL.SILICATE TREATMENT,SULPHUR- 0.015MAX,PHOSPHORUS-0.03MAX.AS PER SPCN. IS:4163-1982,INCLU. RATING i.e.THIN/THICK-SULPHIDE:1.5-1,ALUMINA:1.5-1,SILICATE: 1.5-1,GLOBULAR OXIDE:2.0-1.

ST.SQR.65MMX2.50MTR LONG OR MULTIPLE TO SPEC.BS:3S144-1995 (1999)GD.S144 D LFVD(WITH CAL.SILICATE TREATMENT,SULPHUR- 0.015MAX,PHOSPHORUS-0.03MAX.AS PER SPCN. IS:4163-1982,INCLU. RATING i.e.THIN/THICK-SULPHIDE:1.5-1,ALUMINA:1.5-1,SILICATE: 1.5-1,GLOBULAR OXIDE:2.0-1.

MOD STEPNEY MOUNTING ARRANGEMENT ON RH SIDE FOR UPGRADED MPV 4 by 4 DRG NO 2700 57 32

MOD STEPNEY MOUNTING ARRANGEMENT ON RH SIDE FOR UPGRADED MPV 4 by 4 DRG NO 2700 57 32

DRG NO 2700 57 32

MOD STEPNEY MOUNTING ARRANGEMENT ON LH SIDE FOR UPGRADED MPV 4 by 4 DRG NO 2699 57 31

MOD STEPNEY MOUNTING ARRANGEMENT ON LH SIDE FOR UPGRADED MPV 4 by 4 DRG NO 2699 57 31

DRG NO 2699 57 31

As per specification / Drawings

As per specification / Drawings

MACHINING OF CAP OF 9MM CARBINE IN FINISHED CONDITION DS CAT NO 1005-000860 DC(I)NO 26881-SA DT01.7.16 FROM IC OF CAP (MATERIAL TO BE SUPPLIED BY FACTORY AGAINST BANK GUARANTEE LF NO 0133077013)

MACHINING OF CAP OF 9MM CARBINE IN FINISHED CONDITION DS CAT NO 1005-000860 DC(I)NO 26881-SA DT01.7.16 FROM IC OF CAP (MATERIAL TO BE SUPPLIED BY FACTORY AGAINST BANK GUARANTEE LF NO 0133077013)

1005-000860

MACHINING OF CAP OF 9MM CARBINE IN FINISHED CONDITION DS CAT NO 1005-000860 DC(I)NO 26881-SA DT01.7.16 FROM IC OF CAP (MATERIAL TO BE SUPPLIED BY FACTORY AGAINST BANK GUARANTEE LF NO 0133077013)

MACHINING OF CAP OF 9MM CARBINE IN FINISHED CONDITION DS CAT NO 1005-000860 DC(I)NO 26881-SA DT01.7.16 FROM IC OF CAP (MATERIAL TO BE SUPPLIED BY FACTORY AGAINST BANK GUARANTEE LF NO 0133077013)

1005-000860

A SET OF 04 COMPONENTS OF HR BINO

A SET OF 04 COMPONENTS OF HR BINO

SNAP FASTNER 04 PIECES

IS : 4741-1968

Guide Piece to Drg.no. ARDE/SK/2689/135 Infinished & Hard Condition DS CAT N0.1005-007859. against folio no. 7012097933.

Guide Piece to Drg.no. ARDE/SK/2689/135 Infinished & Hard Condition DS CAT N0.1005-007859. against folio no. 7012097933.

POWER SUPPLY SYSTEM 675 89 SB2 LESS STARTER LEAD ACID 12V BATTERY TO SPECN TY 16 529 357 79 CQA AVL M 13 2005 USE LCSO APPROVED COMPONENT

POWER SUPPLY SYSTEM 675 89 SB2 LESS STARTER LEAD ACID 12V BATTERY TO SPECN TY 16 529 357 79 CQA AVL M 13 2005 USE LCSO APPROVED COMPONENT.

PL REFER OFMK E PROCUREMENT WEBSITE tank.ofmk@ofb.gov.in for full drawings and specifications.

MOD ENGINE HOUSING TO INTEGRATE CUM

MOD ENGINE HOUSING TO INTEGRATE CUMMINS ENGINE FOR 155MM FH GUNS

FLAME SENSOR TO SPECIFICATION NO. OFPM/R&D/SP/MPV/FLAME SENSOR

FLAME SENSOR TO SPECIFICATION NO. OFPM/R&D/SP/MPV/FLAME SENSOR

FLAME SENSOR TO SPECIFICATION NO. OFPM/R&D/SP/MPV/FLAME SENSOR

FLAME SENSOR TO SPECIFICATION NO. OFPM/R&D/SP/MPV/FLAME SENSOR

172.51.016-1/F

172.51.016-1/F

172.51.016-1/F

172.51.016/F

172.51.016/F

172.51.016/F

AMMN.CONT.BOX H-454576 MK1 DRGNO 1A 914454578

AMN.CONT.BOX H-76 MK.1 DRG.NO IA 914 SHEET - 1 PART ISV 74 A SPECIFICATION - IA 948 TO BE PAINTED AS PER DRG.WITH PAINT OLIVE

drs15487p

CRADLE CLAMP AS PER THE DESCRIPTION AND THE BILL OF MATERIAL (ENCLOSED) OF PART NO 1148547

CRADLE CLAMP AS PER THE DESCRIPTION AND THE BILL OF MATERIAL (ENCLOSED) OF PART NO 1148547

Test Data not to apply

est Data not to apply

25487

THERMAL TRANSFER LABEL PRINTER RIBBON MATERIAL

As per Specification

12415454

PRIMARY CARTRIDGE KEY TO DS CAT NO 1398-000099, PT NO. AMG 72924.

PRIMARY CARTRIDGE KEY TO DS CAT NO 1398-000099, PT NO. AMG 72924.

DS CAT NO 1398-000099, PT NO. AMG 72924.

TRIGGER ASSEMBLY TO DS CAT NO 1005 006589 DC(1) NO 26375 SA DT 05/09/07 WITH DETAILS OF LATEST ISSUE INSPECTION TO BE GOVERN BY RELEVANT CLAUSES OF SPECN JSS-1005-04 2006 OF LATE ST ISSUE and ANY OTHER ACCEPTANCE CRITERIA TO BE PROVIDED BY CQA (SA) ISHAPORE

TRIGGER ASSEMBLY TO DS CAT NO 1005 006589 DC(1) NO 26375 SA DT 05/09/07 WITH DETAILS OF LATEST ISSUE INSPECTION TO BE GOVERN BY RELEVANT CLAUSES OF SPECN JSS-1005-04 2006 OF LATE ST ISSUE and ANY OTHER ACCEPTANCE CRITERIA TO BE PROVIDED BY CQA (SA) ISHAPORE

1005-006589

• Machining & Assy.

• 1) Chemical & Mechanical properties as per std. given drawing 2) Dimensional inspection for all dimensions given in the drawing & other parameter which are mentioned in relevant drawing.

sdsad

dsadfsa

42354235

test

demo

123456

est Data not to apply

est Data not to apply

est Data not to apply

FABRIC MERCERISED 140 GM U/D 136+4 CM.

SPECN. NO. IS:514.GRADE -1.

Fabrication of Pant Drill Cotton Navy Blue for Chanda

FABRICATION OF PANT DRILL COTTON NAVY BLUE FOR CHANDA SPECIFICATION: SWO PART No. 20139/70139. MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) DRAWING & SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION.

• As per Specification enclosed.

• As per Specification enclosed.

Fabrication of Pant Drill Cotton Navy Blue with Patch Pocket

FABRICATION OF PANT DRILL COTTON NAVY BLUE WITH PATCH POCKET SWO PART II No. 20064/70064. SPECIFICATION: MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

Fabrication of Trouser Drill White Suit Danger Building for Khamaria

FABRICATION OF TROUSER DRILL WHITE SUIT DANGER BUILDING FOR KHAMARIA SPECIFICATION: SWO PART No. 20137. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) DRAWING & SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

AS PER SPECIFICATION ENCLOSED.

• AS PER SPECIFICATION ENCLOSED.

• AS PER SPECIFICATION ENCLOSED.

Fabrication of Manila Shirt Drill Cotton Khaki Full Sleeve for AFK

FABRICATION OF MANILA SHIRT DRILL COTTON KHAKI FULL SLEEVE FOR AF KHADKI SWO PART II No. 20150/70150. SPECIFICATION: MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

Fabrication of Bush Shirt Drill Cotton Navy Blue Half Sleeve

FABRICATION OF BUSH SHIRT DRILL COTTON NAVY BLUE HALF SLEEVE SWO PART II No. 20138/70138. SPECIFICATION: MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

AS PER SPECIFICATION ENCLOSED.

• AS PER SPECIFICATION ENCLOSED.

• AS PER SPECIFICATION ENCLOSED.

Fabrication of Bush Shirt Drill Navy Blue IFD

FABRICATION OF BUSH SHIRT DRILL NAVY BLUE (IFD) SWO PART II No. 20063. SPECIFICATION: NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) DRAWING & SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

FABRICATION OF MANILA SHIRT DRILL COTTON NAVY BLUE FULL SLEEVES

FABRICATION OF MANILA SHIRT DRILL COTTON NAVY BLUE F/S. SWO PART II No. 20149/70149. SPECIFICATION: NOTE: CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

FABRICATION OF MANILA SHIRT DRILL COTTON NAVY BLUE HALF SLEEVE SWO PART II No. 20148/70148.

SWO PART II No. 20148/70148. SPECIFICATION: MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

CANOPY RELEASE ASSEMBLY WITH WIRE LOOP

DRAWING NO. ADRDE/1233(a)

DRAWING NO. ADRDE/1233(a)

• As per Drawing/Specification

• As per Drawing/Specification

TAPE NYL.26 MM BS300KG. U/D IN ROLL LENGTH OF 105 MTR. (EXCLUDING SAMPLING)

SPECN.NO:-ADRDE/QMS/TDTM/SPECN/84.

NIV BUCKLE V SHAPED WITH SLIDING BAR

DRAWING NO. CQA(GS)/US/562

DRAWING NO. CQA(GS)/US/562

TOWING RING LARGE

Drg. No. 1.3.01-06-01-(b)

Drg. No. 1.3.01-06-01-(b)

TOWING RING SMALL

Drg. No. 1.3.01-06-01-(b)

Drg. No. 1.3.01-06-01-(b)

Catch Trigger for Revolver in finished condition as per Drawing No.-PHMK-III-7-2 MIM “THROUGH MIM ROUTE ONLY”

Catch Trigger for Revolver in finished condition as per Drawing No.-PHMK-III-7-2 MIM “THROUGH MIM ROUTE ONLY”

PHMK-III-7-2 MIM

SNAP HOOK QUICK EJECTOR

ADRDE/1210(c)

ADRDE/1210(c)

• ADRDE/1210(c)

• ADRDE/1210(c)

TUNGSTEN POWDER

CQAM-58 SPECIFICATION

PROVISIONAL SPECIFICATION NO. PROV/S/2599/TC-11/2009/02 AS PER RELEVANT CLAUSE OF SPECIFICATION.

PROVISIONAL SPECIFICATION NO. PROV/S/2599/TC-11/2009/02 AS PER RELEVANT CLAUSE OF SPECIFICATION.

EYE GUARD OPTICAL INSTRUMENT AS PER DRG NO CQA(I) 789/50, MCT-2963/1 (K0000298) FOR HR BINO 8X30R

EYE GUARD OPTICAL INSTRUMENT AS PER DRG NO CQA(I) 789/50, MCT-2963/1 (K0000298) FOR HR BINO 8X30R

MCT-2963/1

OBJ. CAP RIGHT COMPLETE AS PER DRG. NO. MCT-2927/1(K0001756) FOR HR BINO

OBJ. CAP RIGHT COMPLETE AS PER DRG. NO. MCT-2927/1(K0001756) FOR HR BINO

MCT-2927/1

ISPL FOR DHANUSH.

ISPL FOR DHANUSH.

• PRINTING DOCUMENT

• NON-TEARABLE

TECHNICAL MANUAL FOR DHANUSH.

TECHNICAL MANUAL FOR DHANUSH.

• PRINTING DOCUMENT

• NON-TEARABLE

USER HANDBOOK FOR DHANUSH.

USER HANDBOOK FOR DHANUSH.

• PRINTING DOCUMENT

• NON-TEARABLE

MAINTENANCE MANUAL WORKSHOP.

MAINTENANCE MANUAL WORKSHOP.

• PRINTING DOCUMENT

• NON-TEARABLE

MAINTENANCE MANUAL FIELD SERVICE.

MAINTENANCE MANUAL FIELD SERVICE.

• PRINTING DOCUMENT

• NON-TEARABLE

TECHNICAL DESCRIOTION FOR DHANUSH.

TECHNICAL DESCRIOTION FOR DHANUSH.

• PRINTING DOCUMENT

• NON-TEARABLE

RANGE TABLE CONSOLIDATED DHANUSH.

RANGE TABLE CONSOLIDATED DHANUSH.

• PRINTING DOCUMENT

• NON- TEARABLE PAPER PRINTING

PARTS CATALOUGE 1&2.

PARTS CATALOUGE 1&2.

• PRINTING DOCUMENT

• NON-TEARABLE PRINTING

CES SERVICE EDITION FOR DHANUSH.

CES SERVICE EDITION FOR DHANUSH.

OPERATOR'S MANUAL FOR DHANUSH.

OPERATOR'S MANUAL FOR DHANUSH.

• PRINTING DOCUMENT

• NON-TEARABLE PRINTING

HISTORY SHEET (BINDER COMPLETE). HISTORY SHEET BOOK(BINDER COMPLETE) FOR DHANUSH COMPRISING- 1)BARREL/LINER HISTORY SHEET, 2)BREECH RING/JACKET HISTORY, 3)CARRIAGE/MOUNTING HISTORY, 4)DAILY RECORDS OF ROUND FIRED, 5)RECOIL SYSTEM HISTORY, 6)ELECTRONIC UPGRADATION, 7)BACKUP/DIAL SIGHT,FIRE DIRECT CONTROL SYS HISTORY.

HISTORY SHEET (BINDER COMPLETE). HISTORY SHEET BOOK(BINDER COMPLETE) FOR DHANUSH COMPRISING- 1)BARREL/LINER HISTORY SHEET, 2)BREECH RING/JACKET HISTORY, 3)CARRIAGE/MOUNTING HISTORY, 4)DAILY RECORDS OF ROUND FIRED, 5)RECOIL SYSTEM HISTORY, 6)ELECTRONIC UPGRADATION, 7)BACKUP/DIAL SIGHT,FIRE DIRECT CONTROL SYS HISTORY.

• PRINTING DOCUMENT

• NON-TEARABLE PRINTING

INSPECTION LOG BOOK FOR DHANUSH.

INSPECTION LOG BOOK FOR DHANUSH.

• PRINTING DOCUMENT

• NON-TEARABLE PRITING PAPER

Set of EBXL Insulated Cores Laid UP and FR LSZH Polyolefin Sheathed Flexible Cables Confirming to EED 50 12 and EED 50 13 as per Annexure B

Set of EBXL Insulated Cores Laid UP and FR LSZH Polyolefin Sheathed Flexible Cables Confirming to EED 50 12 and EED 50 13 as per Annexure B

STEEL ROUND 65MM DIA TO SPECN:BS:3S144-1995(1999) GRADE S144D LFVD SULPHUR-0.015, PHOSPHOROUS-0.03 SECONDARY REFINING STEEL AS PER SPECN:IS:4163-1982 INCLUSION RATING SHOULD NOT EXCEES THE FOLLOWING:LFVD WITH CALCIUM SILICATE TREATMENT. THIN/THICK SULPHIDE-1.5-1, ALUMINA.1.5-1, GLOBULAR OXIDE 2.0-1,SILICATE 1.5-1.

STEEL ROUND 65MM DIA TO SPECN:BS:3S144-1995(1999) GRADE S144D LFVD SULPHUR-0.015, PHOSPHOROUS-0.03 SECONDARY REFINING STEEL AS PER SPECN:IS:4163-1982 INCLUSION RATING SHOULD NOT EXCEES THE FOLLOWING:LFVD WITH CALCIUM SILICATE TREATMENT. THIN/THICK SULPHIDE-1.5-1, ALUMINA.1.5-1, GLOBULAR OXIDE 2.0-1,SILICATE 1.5-1.

PACKING PREFORMED TO DS CAT.NO. 5305-014097 SHT 1 TO 4

PACKING PREFORMED TO DS CAT.NO. 5305-014097 SHT 1 TO 4

SPRING HELICAL COMPRESSION TO DRG NO GCF-MN 5501(C ) REF.DRG NO. 5360-040480.

SPRING HELICAL COMPRESSION TO DRG NO GCF-MN 5501(C ) REF.DRG NO. 5360-040480.

SPRING HELICAL COMPRESSION TO DRG NO GCF-MN-5502(C) (REF.DRG NO (5360-040481).

SPRING HELICAL COMPRESSION TO DRG NO GCF-MN-5502(C) (REF.DRG NO (5360-040481).

LEVEL,FIRE CONTROL INSTRUMENT AS PER DRG.NO.:IRDE-1135/SA-1

LEVEL,FIRE CONTROL INSTRUMENT AS PER DRG.NO.:IRDE-1135/SA-1

IRDE-1135/SA-1

Elastic Black 3cm Wide Best trade quality as per provisional specification no.-S/2594/CCD army logo/TC-15(a)

Best trade quality as per provisional specification no.-S/2594/CCD army logo/TC-15(a)

• as per attached list (Manufacturing Technology Files )

• as per attached list (Testing / Inspection Facility Files )

Plastic Button Reversible 19 mm in Matching printed pattern ( Thermosetting)

Plastic Button Reversible 19 mm in Matching printed pattern ( Thermosetting) Specification No- IS:1461 1984(second Revision) reaffirmed 2003, Except that shape & design as per annexure "A" attached and feel & finish as per sample held in the custody of OCFS. As per relevant clause of supplementary schedule no. CQA(GS)/SS/346(b)

• as per attached list (Manufacturing Technology Files )

• as per attached list (Testing / Inspection Facility Files )

Mechanised stainless steel metal hooks and Clips with Base (press type) (item Code 1506420449)with specification : Mechanised stainless( steel metal hooks and Clips with Base (Press type) OPF Drawing No.OPF/CLO/IAF/TRS/01

Mechanised stainless steel metal hooks and Clips with Base (press type) (item Code 1506420449)with specification : Mechanised stainless( steel metal hooks and Clips with Base (Press type) OPF Drawing No.OPF/CLO/IAF/TRS/01

Fabrication of Cap Drill Khaki (Suit Danger Building)

FABRICATION OF CAP DRILL KHAKI (SUIT DANGER BUILDING) SWO PART II No. 02361/72361. SPECIFICATION: MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

FABRICATION OF FLAME RETARDANT ACTION OVERALL FOR MSF

FABRICATION OF FLAME RETARDANT ACTION OVERALL FOR MSF SWO PART II No. 20234/70234. SPECIFICATION: MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.

Fabrication of Coat Laboratory

FABRICATION OF COAT LABORATORY SWO PART II No. 20181/70181. SPECIFICATION: MAKE & SHAPE: AS PER APPROVED SAMPLE. NOTE: A) CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY. B) SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICATION, IF REQUIRED.